Bedienungsanleitung Whirlpool ADP 253 WH (Seite 5 von 8) (Englisch)

450668

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

To ensure the dishwasher works at its best, soft

water, i.e. water that is lime-free, is required. The

presence of lime in tap water causes water stains

due to calcium deposits on crockery and glasses.

A water softening system has been built in the

dishwasher to ensure a steady supply of soft

water. This is basically a decalcifying system,

which needs to be regenerated regularly using

special dishwasher salt.

Setting the correct water hardness level:

Set the water hardness level by turning the

selector fitted on the left-hand side of the inner

appliance wall by using a coin. Use the table

below to set the dial to the correct setting:

If the water hardness level falls within category 1

(soft), no salt is required.

To find out the waterhardness level of water in

your area contact your local Water Board or

check the last bill you received.

If provided, a simple test can be employed to set

the hardness level using the hardness test strip.

• Dip the test strip into a glass of water from the

tap.

• Wait for 3 seconds, withdraw the strip from

the water.

• Wait for 1 minute.

• If all the three test squares are still green, set

the hardness selector to 0, and disregard all

instructions about salt usage.

• If one of the test squares becomes red, set

the selector to 1.

• If two of the test squares become red, set the

selector to 2.

• If all of the test squares become red, set the

hardness selector to 3.

How to fill the salt container:

Warning: only use dishwasher salt!

Do not fill the salt container with

unsuitable substances, such as

detergent, as this will cause irreparable

damage to the water softener system.

1. Remove the lower rack.

2. Unscrew the cap by turning it counter-clockwise.

3. When first using the dishwasher: fill the salt

container with approximately 1 litre of water.

4. Fill the salt container to the rim with salt

(using the funnel provided) (when filling for

the first time use min. 1.5 kg and max. 2 kg)

and stir with a spoon handle.

5. Screw the cap back on by turning it

clockwise.

6. Fit the lower rack.

7. After filling the regeneration salt container,

immediately

start a wash programme (the

Prewash programme alone is not sufficient),

so as to eliminate any residual saline solution

straight away and avoid corrosion.

Check the salt level regularly.

Salt level indicator:

The dishwasher is equipped with an electric or

visual salt level indicator (depending on the

model installed).

Electric indicator:

The salt level indicator lamp on the control panel

lights up when the salt container is empty.

Visual indicator:

The green float is clearly visible in the cap

window when the salt container is sufficiently full.

The green float drops and is no longer visible

when the salt container needs to be refilled.

HOW TO FILL THE SALT CONTAINER

Water

hardness

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool ADP 253 WH Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool ADP 253 WH

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info