Bedienungsanleitung Whirlpool ADP 4408 WH (Seite 5 von 9) (Englisch)

450685

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

HOW TO FILL THE SALT CONTAINER

From a water hardness category of 1-2 (medium), before using the

dishwasher, fill the salt container with regeneration salt (to find out the

hardness level of water in your area, contact your local Water Board or

check the last bill you received).

If the water hardness level does not correspond to position 3 on the

selector (factory setting) or if the water hardness level changes:

Set the water hardness level:

setting must be carried out according to the following table:

•

Switch on the appliance (consult the quick reference guide).

•

Select program 2.

•

Press the Start button for at least 5 seconds until the Start indicator

lamp flashes.

•

The Start indicator lamp flashes in relation to the water hardness set

(table, flashing frequency).

•

With each successive touch of the Start button the setting increases

and when it reaches 7 it returns to 1 again.

•

Switch off the appliance (consult the quick reference guide).

The selected setting is now memorized.

Hardness

level

German

degrees

°dH

French

degrees

°fH

mmol/l Clarke

scale or

English

degrees

°eH

Setting

Flashing

frequency

(1x-7x)

1 soft 0 - 5 0 - 9 0 - 0.9 0 - 6.3 1x

1 - 2 medium 6 - 10 10 - 18 1.0 - 1.8 7 - 12.6 2x

2 average 11 - 15 19 - 27 1.9 - 2.7 13.3 - 18.9 3x

3 medium-hard 16 - 21 28 - 37 2.8 - 3.7 19.6 - 25.9 4x

4 hard 22 - 28 38 - 50 3.8 - 5.0 26.6 - 35 5x

4 very hard 29 - 35 51 - 63 5.1 - 6.3 35.7 - 44.1 6x

4 extremely

hard

36 - 60 64 - 107 6.4 - 10.7 44.8 - 74.9 7x

If the water hardness level falls within

category 1 (soft), no salt is required.

How to fill the salt container

Warning: Only use regeneration salts for use in domestic

dishwashers!

Do not fill the salt container with unsuitable substances, such as detergent,

as this will cause irreparable damage to the water softener system.

Remove the lower rack.

Unscrew the cap by turning it counter-clockwise.

When first using the dishwasher: fill the salt container to the rim with

water.

Fill the salt container to the rim with salt (using the filler provided)

(when filling for the first time use min. 1.5 kg and max. 2 kg) and

stir with a spoon handle.

Screw the cap back on by turning it clockwise.

Fit the lower rack.

If regeneration salt is to be added,

immediately

start a wash

programme (rinsing alone is not sufficient) in order to eliminate

any residual saline solution straight away and avoid corrosion.

Salt level indicator

The dishwasher is equipped with an electric or visual salt level

indicator (depending on the model installed).

Electric indicator

The salt level indicator lamp on the control panel lights up when the

salt container is empty.

Visual indicator

The float is clearly visible in the cap window when the salt container is full.

The float lowers and is no longer visible when the salt container is empty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool ADP 4408 WH Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool ADP 4408 WH

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info