PROGRAMS SELECTION
BUTTON
Push “P” button (repeatedly)
until selected program number
is shown on the display
(P1...Px) - see “Table of
programs” below.
START/RESUME BUTTON
Push this button to start the selected program: the
indicator lights up and goes off at the end of the
program.
When the door is opened during a washing cycle,
the cycle is temporarily paused: the Start indicator
blinks. To resume the cycle close the door and
push Start button again.
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute
(0:01 is shown into the display).
If pressed when the dishwasher is switched off,
it drains any possible liquids from dishwasher
(1 minute process).
(see at right for options description)
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary
depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the
EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
Table of programs
Deter-
gent
Consumption
Drying
Phase
Programs
Available
options
Loading instructions
Litres kWh
Minutes
1)
P1
Sensor 40°-70°C
Delay
Antibacterial
rinse
Recommended program for routine
washes, with dried-on food
(e.g. EN 50242).
X 7-14 1.00-1.60 70-155 Full
P2
Pre-Wash cold
Delay Crockery to be washed later. — 4.0 0.03 14 NO
P3
Rapid 45°C
Delay
Lightly soiled crockery, with no dried-
on food.
X 11.0 0.80 30 NO
P4
Eco
2)
50°C
Delay
Antibacterial
rinse
Normally soiled crockery.
Energy-saving program.
X 12.0 1.03 170 Full
P5
Fast Daily 60°C
Delay
Antibacterial
rinse
Normally to heavily soiled crockery. X 10.0 1.30 80 Full
P6
Steam
Delay
Antibacterial
rinse
Program including steam action
dedicated for heavily soiled crockery,
pots and pans. Soaking or hand
pretreatment is no longer needed.
X 14.0 1.70 180 Full
5019 396 03626
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS
QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
Options and display description
SALT INDICATOR
When lit (at the end of the cycle),
the salt reservoir needs to be
refilled.
RINSE AID INDICATOR
When lit (at the end of the cycle),
the rinse aid dispenser needs to
be refilled.
WASH TIME DISPLAY
Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates
the time remaining until program start (h.00) - below 1h (0:min).
If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY
BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
DELAYED START BUTTON
Push the button
(repeatedly) to delay the
start of the program –
delay indicator turns on.
Adjustable from 1 to 24
hours. With each press
of the button, the delay
increases by one hour and
after "h 24" returns to
"h 00”. When this option
is selected the delay
indicator turns on. Then
press the START button.
The dishwasher will start
after the set time.
ANTIBACTERIAL RINSE
3)
This function activates an
antibacterial rinse at the end of
the wash cycle, guaranteeing a
further reduction of bacteria.
Press the button to activate
or deactivate the function.
This function can be used with
the programs indicated in
the table of programs.
The dishwasher door must
be kept shut for the entire
duration of the program in
order to guarantee reduction
of bacteria. If the door is
opened the indicator lamp
starts flashing.
TABLET SETTING
This setting allows to
optimize the cycle
performances according the
type of detergent used.
Push the Tablet button for
3 seconds (until the indicator
lights up) if you are using the
combined detergents in
tablet (rinse aid, salt and
detergent in 1 dose). If you
are using powder detergent
or liquid detergent, the
Tablet indicator on the
control panel has to be off.
