Bedienungsanleitung Whirlpool ADPU 8793 (Seite 3 von 12) (Englisch)

660516

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

EN -3-

First time use

1- salt reservoir

2- rinse aid dispenser

3- detergent dispenser

4- racks system

5,6,7,8- available functions on the panel

9- filters

10- spray arms

Water hardness should be set

only before the first wash or if

water hardness has been

changed

Visual indicator

(depending

on the model).

Unscrew cap.

Fill the salt reservoir with water

before the first wash only.

(depending on the model)

The salt level indicator lamp may remain lit

at the end of several wash cycles. If the

water hardness level falls within category

(soft), no salt is required.

Salt indicator on the control panel Salt indicator on the salt reservoir cap

The indicator lamp lights up when SALT

NEEDS TO BE ADDED.

green: OK.

clear: NEEDS TO

BE ADDED

Daily check

Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)

Screw on the cap.

Salt residual

around the cap

need to be

removed. Some

salt reservoir have

a level indicator

integrated in the

cap (see below

how to check).

- Press and hold together PROGRAM Selection and CANCEL/Off buttons for minimum 3 seconds.

- The current water hardness setting will be visible on the display.

- Press the PROGRAM Selection button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the

next press of the start button will set the level back to 1).

- Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting.

1. Ask your water supply company what the water hardness is... 2. ...enter this value

on your dishwasher

Suggestions for detergent use

German

degrees °dH

French

degrees °fH

English

degrees °eH

Water hardness

level

Insert value is shown

in the display

Gel or Powder

(rinse aid and salt)

Tablets

0 - 5 0 - 9 0 - 6.3 Soft 1

go to step 1

(see “Daily

check”)

6 - 10 10 - 18 7 - 12.6 Medium 2

11 - 15 19 - 27 13.3 - 18.9 Average 3

16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4

if water is

HARD extra salt

needs to be

added

(go to step 1,

“Daily check”)

22 - 28 38 - 50 26.6 - 35 Hard 5

29 - 35 51 - 63 35.7 - 44.1 Very hard 6

36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7

Add salt (never add detergent!)

min. 0.8 kg/max. 1 kg

Water hardness level is

factory set for medium-hard

water (level 4).

Even if you use tablets which

include salt functionality, you

must still add regeneration

salt since such detergents are

not effective enough at

softening hard water.

At first time use, the salt

reservoir has to be filled

independently from water

hardness level (see

description below in step 1

“Daily check”).

Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient).

Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components.

The guarantee is not applicable if faults are caused by such circumstances.

How to set water hardness in order to always assure the best cleaning results

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool ADPU 8793 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info