Bedienungsanleitung Whirlpool AKR 428 NB (Seite 4 von 4) (Englisch)

108469

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Before calling After Sales Service:

1. Check to see if you can fix the problem

yourself (see “Troubleshooting guide”).

2. Switch off the hood for a few minutes and

re-start it to see if the problem has cleared itself.

3. If the malfunction persists, call

After-Sales Service.

Specify:

• The nature of the problem.

• The model.

• The service code (number below

the word SERVICE on the rating

plate inside the hood behind the

grease filter).

• Your full address.

• Your telephone number and area code.

When installing the hood, the minimum distances from the cooktop must be respected, and

the numerical sequence and additional instructions must be followed exactly as indicated on

the Installation sheet.

EXTERNAL EXHAUST MODE

(

- see also instruction sheet)

Cooking fumes and vapours are conveyed

outside through a duct connected to the hood by

means of a collar.

The outlet duct diameter must be the same as

that of the collar.

If a flue-damper is to be installed, check that

it can open and close freely when installation

of the exhaust duct is complete.

The hood can be supplied with one (upper) or

two (upper and rear) exhaust outlet holes.

The hood is usually set up for using the

upper exhaust outlet.

1. The collar must be seated in the upper

exhaust outlet.

Use the rear exhaust outlet (where present).

1. Where fitted, remove the cover closing off the

rear outlet and collar.

2. Some models are fitted with a plastic

deflector that closes off the rear outlet.

If fitted, remove it.

3. Fit the collar in the rear outlet.

4. Put the cover (if fitted) in the upper outlet.

Warning!

If the hood has a carbon filter, this

should be removed.

Check that the switch inside the hood (if fitted)

is in position “A” Extractor; if not, set it to

this position.

AIR CIRCULATION MODE

(

- see also installation sheet)

The air is filtered by a carbon filter and recycled

into the surrounding atmosphere. The filtered air

is released towards the kitchen ceiling.

Warning!

If the hood does not have a carbon

filter, order one and fit it before use.

Check that the switch inside the hood (if fitted) is

on position “F” Filter; if not, set it to this position.

If the plug is provided, close off the upper

exhaust hole.

ELECTRICAL CONNECTION

Before connecting the hood, make sure the

voltage indicated on the rating plate corresponds

to the voltage in your home.

The plate is located inside the hood behind

the grille.

For GB this appliance is supplied without a plug

and is intended for direct connection to fixed

wiring in accordance with national wiring

regulations. An all-pole disconnection switch

with a minimum contact separation of 3 mm must

be included in the fixed wiring in an easily

accessible position.

The Manufacturer shall not be liable for

any damage or problem arising from

the failure to comply with the

above-mentioned instructions.

AFTER SALES SERVICE

INSTALLATION

75004Agb.fm5 Page 10 Tuesday, March 27, 2001 10:55 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AKR 428 NB Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AKR 428 NB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info