Bedienungsanleitung Whirlpool AKR 666 IX (Seite 4 von 6) (Englisch)

109431

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

5019 318

33157

AKR 631-666-812-966

AKR 943-948-952-995-996



Remove the perimeter extraction panel (if relevant) and the grease filter/s.

Pre-assemble the steam deflector on the motor assembly (if relevant): (a.) fit the steam deflector to the rails of the motor

assembly (remove the two travel stop screws from the steam deflector if necessary), (b.) connect up the control panel and

the lamps, (c.) fix in place with the 14 screws (max).

1. Mark a line on the wall right up to the ceiling, corresponding to the centre-line of the hood.

2. Apply the drilling template to the wall: Align the vertical centre-line on the drilling template with the centre-line drawn

on the wall. The template's bottom edge represents the bottom edge of the hood.

3. Place the mounting bracket over the drilling template so that it matches the outlined rectangle. Mark and drill the two

outside holes. Remove the drilling template. Insert two wall plugs in the holes and fix the hood mounting bracket in place

with two 5 x 45 mm screws.

4. Hang the hood on the mounting bracket. Adjust gap (5.) and the horizontal alignment (6.) of the hood.

5. Remove the hood from the bracket. Drill the holes (9. - Ø 8 mm - see step 7.). Insert two wall plugs (10.).

6. Apply the flue mounting bracket G to the wall against the ceiling. (Align the small slot in the bracket with the centre-line

drawn on the wall. See step 1. Fix the bracket in place with two wall plugs (Ø 8 mm) and 2 screws 12).

7. Hang the hood on the bottom mounting bracket. (14.) Fix the hood to the wall with two 5 x 45 mm screws

(ABSOLUTELY NECESSARY). Plug the two holes if they are visible from the outside.

8. Connect an exhaust pipe to the to the collar B, the fumes must be ducted to the outside (extractor version) or towards

the deflector (filter version). Fix the deflector F to the flue support bracket G with 4 screws (2 screws only for 120 cm

wide model). If the collar (bayonet coupling) is not already fitted, insert it on the deflector F and secure it with 1 screw.

9. Make all necessary electrical connections.

10. Apply the flues and fix them with 2 screws (17a) to the flue support G (17b).

11. Slide the bottom section of the flue all the way over the extraction unit until it engages the seat above the hood.

12. (120 cm wide model only) fix the bottom section of the flue to the hood with 2 screws.

Re-fit the grease filter/s and, if a perimeter extraction panel is fitted, check for correct operation.

Important! Only for model AKR 996: proceed with hob selection and manual calibration of the sensors. For this purpose,

read the paragraph on the next page “Important - upon initial installation”.

1. Control panel.

2. Grease filter.

3. Halogen bulbs.

4. Steam deflector.

5. Telescopic flue.

6. Perimeter extraction

panel (if fitted) and

release handle (f3).

7. Sensors (only present on

some models).

INSTALLATION - ASSEMBLY INSTRUCTIONS

IF NL E PGBD GR

31833157.fm Page 8 Friday, April 1, 2005 5:04 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AKR 666 IX Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AKR 666 IX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info