Bedienungsanleitung Whirlpool akr 799 ix (Seite 12 von 12) (Englisch)

133044

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

5019 318 33278

At the end of cooking and when the ambient parameters

have returned to the levels prior to cooking, the system

switches off.

If the parameters are close to the rest condition, the system

forces hood switch-off after 30 minutes.

AIR QUALITY CONTROL mode, LED “L5” (white) on.

The system promptly reacts to Steam/Gas increases and

remains at the set speed for at least 1 minute, before

returning to the lowest speed/switching off.

When the effect of the Steam/Gas has finished and the

ambient parameters have returned to the levels prior to

start, the system switches off.

Press buttons “1”, “2” and “4” to exit this mode”.

Sensor test

This occurs continuously during automatic operation. In case

of a failure, all the LEDs blink (contact the After Sales

Service); in any case, the hood can be used in manual mode.

Manual setting

Switch the hood OFF and keep buttons “1” and “4” pressed

at the same time for 3 seconds”.

LED “L5” blinking.

It is advisable to carry out this operation when:

• the hood is installed for the first time

• the power supply has been disconnected for many hours

or days

• a sudden temperature changes occurs in the kitchen

Cooking hob selection

This operation optimises automatic hood operation; proceed

as follows:

Switch the hood OFF

Keep buttons “1” and “3” pressed at the same time for 3

seconds until the cooking hob in use is displayed.

LED “L1” on: Gas hob

LED “L2” on: Induction hob

LED “L3” on: Electric hob

Press button “1” for cyclic selection of the hob”

Confirmation of the selected hob is displayed by the

corresponding LED blinking 3 times.

After selecting the hob, wait 10 seconds for function

confirmation”.

The default setting is Gas hob.

Maintenance

Grease filters:

Metal grease filters have an unlimited

life and should be washed once a

month either by hand or in a

dishwasher at a low temperature and

with a short cycle. Washing in a

dishwasher can cause grease filters to

turn white, but this in no way affects efficiency.

• Pull out the handle to remove the filter.

Wash the filter and leave it to dry, proceeding in reverse

order to refit it.

Replacing the halogen bulbs:

1. Disconnect the hood from the mains power supply.

WARNING: Wear gloves.

2. Use a small screwdriver to gently prise the lamp cover off

(at the points indicated in Fig. 3).

3. Remove the burnt-out lamp and fit a new one.

WARNING: Replace using 20W max G4 halogen bulbs

only.

Close the lighting unit (snap-on).

Active carbon filter

(filter hoods only):

The carbon filter must be cleaned once a month in a

dishwasher at the highest temperature, using a normal

dishwasher detergent. Wash the filters on their own.

After washing, reactivate the carbon filter by drying it in the

oven at 100°C for 10 minutes.

Change the carbon filter every 3 years.

Fitting the carbon filter:

1. Remove the grease filter.

2. Remove the filter holder by turning the knobs 90°.

3. Fit the carbon filter “i” in the filter holder “h”.

Reverse the above procedure to re-fit the filter holder and

grease filter.

FINNL P I GR

CZ SK H

RUS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool akr 799 ix Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool akr 799 ix

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info