Bedienungsanleitung Whirlpool akr 806 ix (Seite 13 von 16) (Englisch)

133047

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

5019 318 33271

INSTALLATION - ASSEMBLY INSTRUCTIONS

The hood is designed for operation in filter version only: the air is filtered through a carbon filter and recycled in the

room.

The hood is supplied with fixing plugs suitable for most types of walls/ceilings. However, it is necessary to contact a qualified

technician to ascertain the suitability of the materials according to the type of wall/ceiling. The wall/ceiling must be strong

enough to take the weight of the hood.

Fig. 2

Place the template (Fig. 2) supplied on the ceiling directly above the cooktop, matching the centre of the template (R1) with

the centre of the cooktop (R2).

The sides of the template must be parallel to the sides of the cooktop.

Note: The side of the template with the wording “FRONT” corresponds to the hood controls side.

Drill the holes indicated on the template, and insert the plugs. Remove the template.

Fig. 3

Prepare the support bracket A, suitably adjusting the length of the cables according to the following formula:

L (cm)= X-Y-H+3 cm

L = length of cables.

X= distance between ceiling and the cooktop surface.

Y = height of hood body.

H = minimum installation height between the cooktop surface and bottom part of the hood.

After finding the right length, slide the lock nuts along the cables (Fig.3b) until reaching the required length then clamp them

on the cable with a spanner (Fig. 3c).

Important: Respect the minimum distance from burners, indicated on the first page of the manual.

Fig. 4

After preparing the electrical connection, fit the support bracket to the ceiling, running the cables for electrical connection

through the middle hole

Fix with 3 screws.

Important: Detail A (support bracket) is equipped with a wire (yellow-green) which must be connected to the earth of the

house electrical system.

Fig. 5

Fix the hood to the hooking brackets and secure with 1 screw for each bracket (COMPULSORY FIXING).

Fig. 6

Adjust the position of the hood by means of the adjustment screws.

Fig. 7

Insert the control rod in the special seat.

Note! Compulsory coupling direction, with release.

Fig. 8

Fix the connection box to the support bracket on the ceiling with 2 screws.

Carry out the electrical connection and secure the cables with the cable clamp and 2 screws.

Fix the connection box cover with 4 screws.

Important: Replacement of the interconnection cable must be carried out by the authorised after-sales technical service.

Fig. 9

Insert the cover C between the support cables, making sure they enter the slots provided on the cover.

Important: Leave enough cable so that it passes easily through the slot obtained in the cover.

Secure the cover with 3 grub screws already screwed on the support bracket A.

Note: The 3 fixing screws secure the cover by the friction they exert on the cover itself, and therefore must not be completely

tightened.

Fig. 10

Fit the carbon filter, on the back of the grease filter, with the special elements F. Insert the grease filter + carbon filter assembly

on the hood.

IF NL E PGBD GR

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool akr 806 ix Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool akr 806 ix

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info