Bedienungsanleitung Whirlpool AKR 8081 (Seite 9 von 20) (Englisch)

702386

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

EN9

INSTALLATION  ASSEMBLY INSTRUCTIONS

The instructions below, to be carried out in the order in which they are numbered, refer to the gures (with the same step

numbers) provided on the last few pages of this manual.

IMPORTANT: The ue kit must be purchased in order to use the hood in “Extractor Version”; it must be ordered

and tted before use.

1. Mark a vertical centre line on the wall.

2. Place the drilling diagram on the wall (xing it with adhesive tape): the vertical centre line printed on the drilling

diagram must be aligned with the centre line drawn on the wall, and the lower edge of the drilling diagram must be

aligned with the lower edge of the hood.

Drill the 3 holes as shown on the drawing.

IMPORTANT: The bottom edge of the drilling diagram must have a min. distance of 40 cm (for electric hobs) or

45cm (for gas hobs).

3. Remove the drilling template from the wall, x the support bracket to the wall with 2 plugs and 2 screws and insert

the third plug in the lowermost hole.

4. Extractor Version only - Place the ue support bracket on the wall. Drill and insert the wall plugs as shown. Fix the

bracket.

5. Open the perimeter hood panel.

6. Remove the grease lter.

7. Hook the hood onto the support bracket.

8. Tighten the two adjustment screws.

9. Adjust the hood horizontally, using a level and operating on the two adjustment screws.

10. Open the perimeter panel and mark the two holes for nal xing of the hood.

11. Remove the hood from the wall.

12. Drill the holes marked previously.

13. Insert the wall plugs.

14. Reattach the hood to the wall.

15. Fix the hood to the wall using two screws and two washers.

16. Filter Version only - Fit the plastic grille over the hood air outlet hole.

17. Extractor Version only - Fit the collar onto the hood air outlet hole.

18. Fit the power cable in the special housing.

19. Secure the cable to the cable clamp.

IMPORTANT: This operation is compulsory. It will prevent accidental disconnection of the power cable.

Carry out the connection to the household electrical system.

20. Extractor Version only - Connect an exhaust pipe to the collar for the expulsion of fumes.

21. Filter Version with ues only - Fix the deector to the ue support bracket and connect the exhaust pipe to the

deector.

22. Filter or Extractor Version with ues only - Fit the ues in the relevant seat above the hood.

23. Filter or Extractor Version with ues only - Slide the top section upwards and x the ues with two screws as

shown.

24. Filter Version only - Fit the carbon lter onto the back of the grease lter, hooking it with the two rods.

25. Fit the grease lter and close the front panel.

Check for correct hood operation, referring to the hood description and use section.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AKR 8081 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AKR 8081

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info