Bedienungsanleitung Whirlpool AKR3580 (Seite 2 von 4) (Englisch)

702101

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

ELECTRICAL CONNECTION

This operation must be performed by a qualied technician.

• The electrical connections must

comply with local regulations.

• The earthing of this appliance is

compulsory by law.

• Do not use an extension cord.

Earth

(yellow/green)

IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate.

ASSEMBLY

After having cleaned the perimeter surface,

apply the supplied gasket to the hob as shown in

the gure.

Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction.

NOTE: the power supply cable must be long enough to permit its upward extraction.

To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and

fasten them by means of their screws in accordance with the thickness of the worktop (see the following gures).

Top 20 mm

Top 30-50 mm

ADJUSTMENT TO DIFFERENT TYPES OF GAS

If the appliance is intended to operate with a dierent gas from the gas type stated on the rating plate and information

label on the top of the hob, change the injectors.

Remove the information label and keep it with the instructions booklet.

Use pressure regulators suitable for the gas pressure indicated in the Instruction.

• The gas nozzles must be changed by After Sales Service or a qualied technician.

• Nozzles not supplied with the appliance must be ordered from After Sales Service.

• Adjust the minimum setting of the taps.

NOTE:when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will go.

IMPORTANT: should you experience diculty in turning the burners knobs, please contact the After Sales Service

for the replacement of the burner tap if found to be faulty.

REPLACING THE INJECTORS see the injector table in the Instruction

• Remove grids (A).

• Extract burners (B).

• Using a socket spanner of the appropriate size unscrew

• the injector (C), unscrew the injector to be replaced.

• Replace it with the injector suitable for the new type of gas.

• Re-assemble the injector in (D).

• If you have a multiple crown burner use side spanner to

• replace the injector (E).

Before installing the hob, remember to ax the gas calibration

plate supplied with the injectors in such a way that it covers the

existing information relating to gas calibration.

ADJUSTING MINIMUM GAS SETTING OF TAPS

To ensure that the minimum setting is correctly adjusted, remo-

ve the knob and proceed as follows:

• tighten screw to reduce the ame height (-);

• loosen screw to increase the ame height (+).

The adjustment must be performed with the tap in minimum

gas setting position (small ame)

• The primary air of the burners does not need to be adjusted.

• At this stage, light up the burners and turn the knobs from

max position

to minimum position to check ame

stability.

Upon completion of adjustment, reseal using sealing wax or an

equivalent material.

WARNING

This operation must be performed by a qualied technician.

WARNING

REFERENCE TO LOCAL REGULATIONS

The installation and maintenance of the appliance must be carried out by a qualied skilled technician in accordance

with the regulations in force, and in particular:

- Decree of 2 August 1977

Technical and Safety Rules applicable to fuel gas and liqueed hydrocarbon installations located within residential

buildings and outbuildings.

- Standard DTU P 45 - 204

Gas installations (formerly DTU no. 61-1 - Gas installations April 1982 + supplement no. 1 of July 1984).

- Departmental Health Regulations

For appliances connected to the mains electricity supply.

- Standard NF C 15-100

Low-voltage electrical installations - Standards.

The appliance is supplied with a 1/2” threaded conical end to be connected to the gas supply (according to ISO regula-

tions ISO 7/1 RP 1/2).

The connection must be eected in accordance with standard NBN D 51-003 using rigid piping or in accordance with

specications sheet A.R.G.B./03 using exible tubing.

The appliance must be installed complete with an AGB-approved stop valve.

AFTERSALES SERVICE

Before calling the After-Sales Service, make sure you can give the following information:

- type of fault or problem;

- exact model (written on the label axed to the instruction/warranty);

- service number that follows the word SERVICE on the rating plate under

the hob and on the label axed to instruction/warranty;

- your complete address and phone number.

If any repairs are required, please contact an authorised After-Sales Service, as indicated in the warranty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AKR3580 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AKR3580

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info