Bedienungsanleitung Whirlpool AKT 325 (Seite 2 von 2) (Englisch)

662518

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

• The lava stone tray and the grill can be washed in the

sink but they are better washed in the dishwasher.

• After each cooking empty the residual fats from the lava

stone and wash it carefully. This is to prevent unpleasant

smells during cooking.

• Every 2 to 3 cookings wash the lava stone with running

water.

• Replace the lava stones about twice a year, depending

on frequency of use.

• Remove and dispose of all used lava stones and clean all

surrounding areas and accessories of the appliance.

• Replace uniformly all the new lava stones.

• Clean the heating element very carefully using a dry

cloth or a cloth dampened with water.

• Be careful: do not let water penetrate into the

appliance.

• Do not use steam jet cleaners because the humidity

could infiltrate into the appliance making it dangerous.

TROUBLESHOOTING GUIDE

The heating element does not work:

Check whether :

- The ON indicator light is off.

- Mains electrical power is on.

- The heating element is faulty. In this case disconnect

immediately the power cable and call the After-Sales

Service.

There are unpleasant smells:

- Check whether there are residues of cooking fat on

the lava stone tray.

AFTER-SALES SERVICE

Before contacting After-Sales Service:

• See if you can solve the problem yourself with the help

of the suggestions given in chapter “Troubleshooting

Guide”.

If after the above checks the fault persists, contact the

nearest After-sales Service.

Please give:

• a brief description of the fault;

• the type and exact model of the hob;

• the service number (i.e., the number that follows the

word SERVICE on the rating plate, located under the

hob). The service number is also indicated on the

warranty booklet;

• your full address;

• your telephone number and area code.

If any repairs are required, please contact an

authorised

After-sales Service

(to guarantee that original spare parts

will be used and repairs carried out correctly).

Failure to comply with these instructions may

compromise the safety and quality of the product.

INSTALLATION

Recommendations

Important: Before any installation or maintenance

operation, disconnect the barbecue from the mains

power supply.

• Electrical connections must be made before connecting

the appliance to the electricity supply.

• Installation must be performed by a qualified technician

according to the manufacturer's instructions and current

local regulations.

• After unpacking the barbecue, check that there has

been no damage during transport.

If in doubt, contact

the nearest dealer or Authorised After Sales

Service.

Preparation of fitted cabinet

• Perform all required cuts on the work top before

inserting the appliance. Carefully remove all chips or

residue which could impair efficient operation of the

appliance.

• The barbecue must be recessed in a work top with a

thickness of min. 30 and max. 50 mm.

• Insert a separator panel at a minimum distance of

20 mm from the bottom of the barbecue, so that it is

not accessible to the user.

• If the barbecue is to be installed next to a column unit, leave

a distance of at least 300 mm from the barbecue edge.

• Make an opening in the worktop, observing the

dimensions specified.

Fit the seal supplied onto the hob (if not already present),

after carefully cleaning the application surface.

ASSEMBLY

After having cleaned the perimeter surface, apply the

supplied gasket to the hob as shown in the figure.

Important:

before installing the barbecue, remove any

plastic protection film applied.

Ensure that the opening made in the worktop to house the

barbecue corresponds to the dimensional drawing

specifications, within the relative tolerances.

Never force the barbecue into the worktop.

•

For installation

, use the relative brackets and screws

supplied.

Position the hob in the work top opening made respecting

the dimension indicated on first page.

NOTE:

The power supply cable must be long enough to

permit its upward extraction.

To secure the hob, use the brackets

(A)

provided with it.

Fit the brackets into the relevant bores shown by the

arrow and fasten them by means of their screws in

accordance with the tickness of the work top (see fig. 1).

Electrical connection

• Regulations require that the appliance is earthed.

• The electrical connection must be made by a qualified

technician according to the manufacturer's instructions

and current local regulations.

• The installer is responsible for the correct electrical

connection of the appliance and the observance of the

relative safety standards.

• To comply with directives governing safety, during

installation use a single-pole switch with a minimum gap

between contacts of 3 mm.

• Do not use multiple plug adapters or extension leads.

• After installation, electrical parts must not be accessible.

Connection to the electrical mains

Note:

the yellow/green earthing wire

(B)

must be connected to

the screw. If the power cable is not yet connected:

• strip approx. 70 mm of sheath from the power supply

cable

• strip approx. 10 mm of sheath from the wires

• open the terminal board

(C)

by pressing the side tabs

by means of a suitable tool.

• insert the power cable

(D)

in clamp

(E)

and connect

the wires to the terminal board.

• close the terminal board cover.

• after the electrical connection, insert the hob from the

above and secure on the fixing brackets as shown in figure 1.

Declaration of conformity

• This cooktop is suitable for contact with foodstuffs and

complies with EEC (CE) Regulation n. 1935/2004.

• This cooking hob has been designed to be used only for

cooking Any other use (such as heating a room) is

improper and dangerous

• This cooking hob has been designed, constructed and

marketed in compliance with:

- safety objectives of the “Low Voltage” Directive 2006/

95/CE (which replaces 73/23/CEE and subsequent

amendments).

- protection requirements of EEC Directive “EMC”

89/336;

- requirements of EEC Directive 93/68.

Fig. 2

Fig. 3

Fig. 1

Whirlpool AKT 325 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info