Bedienungsanleitung Whirlpool AKT 352 (Seite 4 von 4) (Englisch)

662521

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

ADJUSTING MINIMUM GAS SETTING OF TAPS

To ensure that the minimum setting is correctly adjusted,

remove the knob and proceed as follows:

• tighten the screw to reduce the height of the flame (-)

• loosen the screw to increase the height of the flame (+)

The adjustment must be performed with the tap in minimum

gas setting position (small flame) .

• The primary air of the burners does not need to be

adjusted.

• At this stage, light up the burners and turn the knobs

from max position to minimum position to

check flame stability.

Upon completion of adjustment, reseal using sealing wax or

an equivalent material.

CARE AND MAINTENANCE

To maintain your hob in perfect conditions, clean it after every use, removing any food spills.

Before any cleaning operation, disconnect the hob from the mains and wait for it to cool down.

CLEANING THE HOB SURFACE

• All the enamelled and glass parts should be cleaned with warm water and neutral solution.

• Stainless steel surfaces may be stained by calcareous water or aggressive detergents if left in contact for too long. Any

food spills (water, sauce, coffee, etc.) should be wiped away before they dry.

Clean with warm water and neutral detergent, and then dry with a soft cloth or chamois. Remove baked-on dirt with

specific cleaners for stainless steel surfaces.

• Do not use abrasive or corrosive products, chlorine-based cleaners or pan scourers.

• Do not use vapour cleaning appliances.

• Do not use flammable products.

• Do not leave acid or alkaline substances, such as vinegar, mustard, salt, sugar or lemon juice on the hob.

CLEANING THE HOB PARTS

• Grids, burner caps and burners can be removed to be cleaned.

• Clean them by hand with warm water and non-abrasive detergent, carefully removing any food residues and checking

that none of the burner openings is clogged.

• Rinse and dry carefully.

• Refit burners and burner caps correctly in the respective housings.

• When replacing the grids, make sure that the panstand area is aligned with the burner and that the burner feet are fitted

in the respective housings on the hob surface. In the case of single grids, make sure that they fit on the burner cap

protuberance.

• Models equipped with electrical ignition plugs and safety thermocouples require thorough cleaning of the plug end in

order to ensure correct operation. Check these items frequently, and if necessary, clean them with a damp cloth. Any

baked-on food should be removed with a toothpick or needle.

Note: to avoid damaging the electric ignition device, do not use it when the burners are not in their housing.

TROUBLESHOOTING GUIDE

The hob may not work or work incorrectly. Before calling the After-Sales Service, refer to the Troubleshooting Guide to

determine the problem.

1. The burner fails to ignite or the flame is not even

Check that:

• The gas or electrical supplies are not shut off and especially that the gas supply tap is open.

• The gas cylinder (liquid gas) is not empty.

• The burner openings are not clogged.

• The plug end is not dirty.

• All the burner parts have been positioned correctly.

• There are no draughts near the hob.

2. The burner does not stay lit

Check that:

• When lighting the burner, the knob has been pressed for enough time to activate the protection device.

• The burner openings are not clogged near the thermocouple.

• The end of the thermocouple is not dirty.

• The minimum gas setting is correct (see relevant paragraph).

3. The containers are not stable

Check that:

• The bottom of the container is perfectly flat

• The container is centered on the burner.

• The grids have not been exchanged or positioned incorrectly.

If after the above checks the fault still occurs, get in touch with the nearest After Sales Service.

AFTER-SALES SERVICE

Before calling the After-Sales Service, make sure you can give the following information:

- type of fault or problem;

- exact model (written on the Product Description Sheet and Warranty);

- service number that follows the word SERVICE on the rating plate under the hob and on the Warranty;

- your complete address and phone number.

If any repairs are required, please contact an authorised After-Sales Service, as indicated in the warranty.

Note: Failure to comply with these instructions may compromise the safety and quality of the product.

Manufacturer:

Whirlpool Europe S.r.l.

Viale G. Borghi, 27

21025 Comerio (VA)

ITALY

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AKT 352 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info