Bedienungsanleitung Whirlpool AKZ 445 IX (Seite 1 von 3) (Englisch)

450516

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

INSTALLING THE BUILT-IN / UNDER THE

COUNTER COLUMN OVEN

Recommendations

Important: Disconnect the oven from the

mains before carrying out any installation

work or servicing.

•

Installation must be carried out by a qualified

technician in accordance with the manufacturer's

instructions and in compliance with local regulations.

•

Unpack the oven and make sure that the

appliance has not been damaged during transport

and that the oven door closes properly.

If you

are not sure contact the dealer or the

nearest service centre.

•

After removing the oven from its packaging,

leave it on the polystyrene base to prevent it

from being damaged.

•

When installing the oven it is advisable to wear

protective gloves.

•

Do not lift the oven by the door handle. Get hold

of it using the side openings provided.

Preparing the housing unit

•

Kitchen units in contact with the oven must be

heat resistant (80 °C min).

•

Cut the kitchen unit to fit before installing the

appliance. Carefully remove any shavings or

sawdust that could prevent the appliance from

running properly.

•

The dimensions of the oven and unit are shown

in figures 1-2-3.

•

To allow for proper ventilation, an opening

should be left at the bottom of the kitchen unit.

Pay attention to the dimensions in the diagram.

When installation has been completed, the

bottom of the oven must be inaccessible.

•

Ovens that are not equipped with a cooling system

cannot be installed in split level units (fig 2).

•

When installing, make sure that the sides of the oven

do not touch the adjacent kitchen units (fig. 4-5).

•

When installing ovens under the worktop, leave

a minimum clearance of 5 mm between the

upper edge of the oven and the lower edge of the

worktop (fig. 6).

In order for the appliance to

operate properly, this clearance must never

be obstructed.

•

If the kitchen unit is not securely fixed to the wall,

it must be anchored with standard brackets (G)

(fig. 7) available on the market.

Electrical connection

Regulations require that the appliance be

earthed.

•

Connection to the mains must be carried out by a

qualified electrician in accordance with the

manufacturer's instructions and in compliance

with local regulations.

•

The installer is responsible for connecting

appliances correctly to the mains and for

observing the safety regulations.

•

The oven power cable must be long enough to

connect the built-in appliance to the mains.

•

Observance of safety directives requires that a

multi pole switch with a minimum contact gap of

3 mm be used for the installation.

•

Do not use multiple plug adapters or extension

leads.

•

After the oven has been installed, the electrical

components must be inaccessible.

Connecting the oven to the power

supply

•

Make sure that the voltage indicated on the rating

plate is the same as the mains voltage. The rating

plate is on the front edge of the oven (visible

when the door is open).

•

If the oven does not have a power supply cable

proceed as follows:

Remove the two fastening screws of the

terminal box cover located on the bottom part

of the oven's rear covering.

Remove the cover to gain access to the terminal

box and insert the power cable (see table)

through the opening located on the bottom of

the oven.

Connect the cable to the terminal box, tighten

the screws as far as they will go and secure it to

the cable fastener.

Put the cover back on by inserting the two blades

in the slots and fasten it with the two screws.

Securing the oven

•

Lift the oven getting hold of it by the openings on

the sides and insert it into the housing unit, being

careful not to trap the power supply cable (fig. 8).

•

Center the oven in the housing unit before

securing it.

•

Make sure that the plastic spacers (if provided)

are positioned correctly in the fastening holes.

Then anchor the oven to the housing unit with

the screws provided.

Power supply cable table

N° of conductors Type of cable

1N+

H05 RR-F 3 X 1.5 mm²

(Switzerland only)

10200149aGB.fm Page 2 Monday, September 5, 2005 2:24 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AKZ 445 IX Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AKZ 445 IX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info