Bedienungsanleitung Whirlpool AKZM 8790 (Seite 5 von 29) (Englisch)

502323

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

EN4

PREPARING THE HOUSING UNIT

• Kitchen units in contact with the oven must be heat resistant (min 90°C).

• Carry out all cabinet cutting work before fitting the oven in the housing and carefully remove all wood chips and sawdust.

• After installation, the bottom of the oven must no longer be accessible.

• For correct appliance operation, do not obstruct the minimum gap between the worktop and the upper edge of the oven.

ELECTRICAL CONNECTION (only in some models)

Make sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The dataplate is on the front

edge of the oven (visible when the door is open).

• Power cable replacement (type H05 RR-F 3 x 1.5 mm

) must be carried out by a qualified electrician. Contact an

authorized service centre.

• The oven is programmed to operate with power absorption above 2.5 kW (indicated by “HIGH” in the settings) which is

compatible with a domestic power supply above 3kW. If the household has a lower power supply, the setting must be

lowered (“LOW” in the settings). The table below details the recommended electrical power settings for the various

countries.

GENERAL RECOMMENDATIONS

Before use:

- Remove protective cardboard pieces, protective film and adhesive labels from accessories, induction plate and cooking

vessel.

- Remove the accessories from the oven. Position the induction plate at the third level and plug it in.

- Place the cooking vessel on the induction plate and fill it in with 200g of water.

- Select the Top Finishing function and run the oven for approximately one hour to eliminate the smell and fumes from the

insulating materials and protective grease.

During use:

- Do not place heavy objects on the door as they could damage it.

- Do not cling to the door or hang anything from the handle.

- Do not cover the inside of the oven with aluminium foil.

- Never pour water into the inside of a hot oven; this could damage the enamel coating.

- Never drag pots or pans across the bottom of the oven as this could damage the enamel coating.

- Make sure that the electrical cables of other appliances do not touch hot parts of the oven or become trapped in the door.

- Do not expose the oven to atmospheric agents.

- Never pour water on the induction plate when inserted into the oven or when it is hot; this could damage the glass or the

enamel coating.

- Insert and remove the induction plate carefully in order to avoid accidental damage to the glass and/or electrical plug.

- Before using the oven in standard mode (without induction), completely remove the induction plate from the oven.

Leaving the induction plate in the oven could damage it.

After Use:

- Allow the induction plate to cool down before removal if cleaning is required. When the induction plate is removed from

the oven, ensure the supplied socket cover is used to prevent dirt entering the electrical socket (Fig. 1).

Country Setting

Germany High

Spain Low

Finland High

France High

Italy Low

Holland High

Norway High

Sweden High

UK Low

Belgium High

Fig. 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AKZM 8790 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AKZM 8790

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info