Bedienungsanleitung Whirlpool ART890 (Seite 3 von 3) (Englisch)

757590

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

TROUBLESHOOTING

What to do if... Possible reasons Solutions

The control panel is

switched o, the appliance

does not work.

The appliance may be in On / Stand-by

mode.

There may be an appliance power

supply problem.

Turn the appliance on pressing the On/Stand-by button. Check that:

• there is not a power outage;

• the plug is properly inserted in the power socket and the mains

double-pole switch (if present) is in the correct position (i.e. allows

the appliance to be powered);

• the household electrical system protection devices are ecient;

• the power cable is not damaged.

The inside light does not

work.

The light may need to be replace. Models with LED lights: contact the authorised Technical Assistance

Service.

The appliance may be in On / Stand-by

mode.

Turn the appliance on pressing the On/Stand-by button.

The temperature inside the

compartments is not low

enough.

There could be various causes (see

“Solutions”).

Check that:

• the doors close properly;

• the appliance is not installed near a heat source;

• the set temperature is adequate;

• the circulation of air through the ventilation of the appliance is

ensured.

There is water on the

bottom of the refrigerator

compartment.

The defrost water drain is blocked. Clean the defrosting water drain (see section “Cleaning and

Maintenance").

The front edge of the

appliance, at the door striker

seal, is hot.

This is not a defect. It prevents

condensation from forming.

No solution is necessary.

The red

icon is ashing

and a sound signal is

activated

Door open alarm

It is activated when the refrigerator and/

or freezer compartments door remains

open for a prolonged period of time.

To turn the sound signal o, close the open door of the product.

The red

icon is ashing,

a sound signal is activated

and the icon is

activated.

Blackout alarm

This activates when there is a prolonged

interruption to the power supply which

has caused an increase in temperature

in the freezer compartment.

Note: until the blackout alarm is

deactivated, you cannot set a dierent

temperature for the product.

Before turning o the sound signal, it is recommended that you pay

attention to the temperature shown on the temperature display,

corresponding to the highest temperature reached in the freezer

compartment during the power cut. To turn the sound signal o,

briey press the “Turn o sound alarm” button.

After pressing the button, the temperature display will again show

the temperature set. If the freezer compartment has not yet reached

the optimal temperature for the preservation of the food, the

freezer compartment temperature alarm may activate (see freezer

compartment temperature alarm). Check the condition of the food

before consuming it.

The red

icon is lit up

(without ashing), a sound

signal is activated and the

freezer temperature display

is ashing.

Freezer compartment temperature

alarm

The freezer compartment temperature

alarm indicates that the compartment

is not at the optimum temperature. This

may occur: when using for the rst time,

after defrosting and/ or cleaning, when

freezing large quantities of food or

when the door to the freezer does not

close completely.

To turn o the sound signal, briey press the “Turn o sound alarm”

button (the temperature display will stop ashing). When the

optimum temperature conditions have been reached, the red icon will

automatically turn o. If the freezer compartment temperature alarm

continues, contact the Authorised Technical Assistance Service.

The red

icon will

light up, a sound signal is

activated and the letter “F”

is ashing on the display.

Malfunction alarm

The alarm indicates the malfunction of a

technical component.

Call the authorized Technical Assistance Service. To turn the sound

signal o, briey press the “Turn o sound alarm” button.

400011195067

You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:

• Visiting our website docs . whirlpool . eu

• Using QR Code

• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When

contacting our After-sales Service, please state the codes provided on your product's identication plate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool ART890 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool ART890

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info