Bedienungsanleitung Whirlpool arz 726 w b (Seite 7 von 28) (Englisch, Holländisch)

342085

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

INSTALLATION (FOR 60 cm DEEP MODELS ONLY)

Installing Custom Wood Panels

Remove any packing tape.

Remove the refrigerator and freezer door trims from the

hinge side of each door by pulling the trim away from the

bottom of the door first.

Partially unscrew the two screws that hold the top trim in

place. It is not necessary to completely remove the screws.

Loosen the screws approximately 6.35 mm from the trim to

allow the panels to slide freely.

Remove the existing door panels, if panels were provided.

Slide custom door panels into place.

NOTE

: The freezer door panels may require 3.18 mm cardboard

fillers behind the panels to keep them from being loose in that area.

Replace the hinge side trims by inserting the notched end

under the top trim first.

Tighten the two top trim screws.

To remove the base grille:

Open the refrigerator and freezer doors 90°.

Remove screws from the base grille using a screwdriver.

NOTE:

Do Not Remove Tech Sheet that is fastened behind the

base grille.

To replace the base grille:

Open the refrigerator and freezer doors to 90°.

Position the base grille in front of the refrigerator and replace

the screws.

Leveling Your Refrigerator

Your refrigerator has a front and rear roller at the base of the

product on each side. All four rollers can be adjusted from the

front of the product. If your refrigerator seems unsteady or you

want the doors to close easier, adjust the refrigerator's tilt

using the instructions below:

Check the installation location to be sure that you have the

proper clearance for the refrigerator. (See the “Space

Requirements” section.)

Plug into a grounded 3 prong outlet.

Move the refrigerator into its final position.

Open the refrigerator and freezer doors to locate the leveling

bolts at the left and right of the refrigerator base. If your

refrigerator has a base grille, remove it (see “Base Grille”

earlier in this section).

NOTE

: The top bolt will adjust the rear of the refrigerator,

and the bottom bolt will adjust the front of the refrigerator.

Use a 12.70 mm socket wrench to adjust the leveling bolts.

Turn the leveling to the right to raise that side of the

refrigerator or turn the leveling bolt to the left to lower that

side. It may take several turns of the leveling bolts to adjust

the tilt of the refrigerator.

NOTE

: Be careful not to unscrew the leveling bolts too much

when lowering the refrigerator. The bolt head will start to

come away from the refrigerator when in the lowest position.

If the screw does come out of the rear roller bracket, the

compartment access cover on the back of the refrigerator will

have to be removed to reinstall the bolt.

Side Trims

Top Trim Screws

Door Panels

Filler Panels

Rear Leveling Bolt

Front Leveling Bolt

3gb33001.fm5 Page 37 Monday, August 20, 2001 3:48 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool arz 726 w b Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info