Bedienungsanleitung Whirlpool awa 6122 (Seite 12 von 18) (Englisch)

314372

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

GB 12

Washing machine exterior and control

panel

•

Clean with a soft damp cloth.

•

If necessary, a neutral household cleaner can be

applied (do not use aggressive or abrasive products).

Lid seal

•

Clean from time to time with a damp cloth.

Water inlet hose(s)

•

Check the hose regularly for brittleness and

cracks. Replace if necessary.

TROUBLESHOOTING GUIDE

This washing machine is equipped with automatic

safety functions which detect and diagnose faults at

an early stage and allow you to react appropriately.

Often, however, the faults detected are small

enough to be solved in a matter of minutes.

For example:

*The washing machine does not start, no

lamp lights up.

Check whether:

•

the washing machine is plugged in.

•

the wall socket is functioning correctly

(use a table lamp or similar).

•

the

“On/Off”

button is pressed.

*The washing machine does not start, but

the pilot light is on and the “Start” lamp

is flashing.

Check whether:

•

the programme has been changed.

Press the “Start” button again.

*The washing machine does not start, but

the pilot light and the “Start” lamp are

on.

Check whether:

•

the washing machine lid is properly closed. Open

and close it again.

*The washing machine stops during the

programme.

Check whether:

•

the “Rinse Hold” button is pressed: terminate

this option by pressing the button again.

•

the programme has been changed. Reselect the

desired programme and press the

“Start”

button.

•

the programme has not been started (the “Start”

lamp is flashing). Press the

“Start”

button.

•

the safety system of the washing machine was

activated. See fault description table.

*Detergent and additive product

residues in dispenser at end of wash.

Check whether:

•

the detergent dispenser is properly installed and

is not blocked (see “Care and maintenance”).

•

the foreign body trap in the water inlet hose is

not blocked (see “Care and maintenance”).

*The washing machine vibrates during

the spin cycle.

Check whether:

•

the washing machine is levelled and that all the feet

are adjusted (see “Installation”).

•

the transport bracket has been removed. Before

starting up the washing machine, the transport

screws and the transport bracket MUST be

removed (see “Installation”).

*Final spin results are poor.

Note:

The washing machine has an unbalance

detection and correction system. If individual heavy

items are loaded (a bathrobe, for example), this

system may reduce the spin speed automatically or

interrupt the spin if it detects too great an

unbalance at the start of the spin, in order to

protect the washing machine.

Check whether:

•

the pump impeller is obstructed (see “Cleaning

the foreign body trap”).

•

if the laundry is still too wet at the end of the

programme: possibly add other items of clothing

and repeat the spin cycle.

•

there is foam on the wash: repeat a rinse-spin

cycle to eliminate excess of detergent.

Excessive foam formation may also prevent

spinning.

3GB10242.fm Page 12 Friday, March 12, 2004 6:34 PM

Black process 45.0° 100.0 LPI

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool awa 6122 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info