Bedienungsanleitung Whirlpool AWE 6722 (Seite 2 von 2) (Englisch)

70489

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Whirlpool is a registered trademark of Whirlpool USA

5019 312 10450

Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized

conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the

values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

The data on the “Energy Label” refer to the programme “Cotton 60°C”.

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains

the water out.

1. Load the machine, close the drum doors and

check that they are properly locked.

2. Add detergents and additives into the dispenser to

no more than the “MAX” level mark, as follows:

• Programme with pre and main wash

• Main wash programme without prewash

• Fabric softeners and conditioners

• Chlorine bleach

• Stain remover agents

• Anti-scale agents (if necessary)

3. Press the “On/Off” button.

The lamp of the “Start” button flashes.

4. Turn the programme selector knob to the

desired programme. The lamp of the

programme’s standard spin speed lights up.

Selecting or deselecting an option can be done

at any time during the programme. The option

will be applied as long as the corresponding

programme phase has not been executed yet.

“Eco” button

• The duration of the wash is extended and the

max temperature reduced to save up to 40% of

energy compared to a normal wash but

maintaining good washing results.

“Easy Ironing” button

• Can be used together with “Cotton”, “Synthetic”

and “Daily Mixed” programmes to make ironing

easier.

• Increases the water quantity in rinsing and the

clothes are spun in a softer manner.

“Intensive Rinse” button

• The amount of water is increased to ensure a

more intensive rinse.

• This option is particularly suitable for areas with

very soft water, washing baby linen and people

with skin allergies.

“Rinse Hold” button

• The laundry remains in the last rinse water without

progressing to the final spin cycle to avoid creasing

and prevent colours from fading.

• This option is particularly recommended for the

“Synthetic” , “Delicate” and “Daily

Mixed ” programmes.

• This function is particularly useful if you want to

postpone spinning to a later time, or if you want

to drain only.

• As soon as the appliance stops in the rinse hold,

the lamp of the “Start” button flashes.

CONSUMPTION DATA

Programme

Temperature Selector

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)

Cotton 95 5.0 66* 1.85 2:05

Cotton 60 5.0 55 0.95 2:05

Cotton 40 5.0 55 0.60 2:05

Daily Mixed 40 3.0 49 0.48 1:00

Synthetic 60 2.0 56 0.80 1:30

Synthetic 40 2.0 56 0.45 1:20

Delicate 40 1.5 60 0.60 0:45

Wool 40 1.0 60 0.50 0:40

Handwash 30 1.0 60 0.30 0:50

PREPARATION OF WASH CYCLE

SELECT THE DESIRED OPTION

Appliance in “Rinse Hold”:

• Press the “Rinse Hold” button or the flashing

“Start” button: the programme will terminate

automatically with the selected spin cycle.

• If you do not wish to spin the clothes, turn the

programme selector knob to the “Drain”

programme and press the “Start” button again.

Spin Speed selection button

• Every programme has an automatically preset

spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spin is

cancelled and the programme ends with a drain

cycle.

The “Start Delay” button allows the user to run

the machine at his convenience, for example at

night when electricity is cheaper.

• Select programme, spin speed and options.

• Press the “Start Delay” button several times to

select a delay time of 1, 3, 6, 9 or 12 hours.

The corresponding indicator lamp flashes.

• Start the programme (see next paragraph).

As the delay time decreases, the

corresponding indicator lamp flashes.

• The flashing light of the delay indicator lamp

goes out when the programm starts.

The delay time can still be modified after the

“Start” button has been pressed:

To decrease the delay time

• (Repeatedly) press the “Start Delay” button.

• Note, however, that the selected wash

programme starts IMMEDIATELY as soon as you

push “Start Delay” with the “1h” lamp flashing.

To increase the delay time

• Switch the washing machine off by pushing the

“On/Off” button.

• Turn the programme selector to a different

programme.

• Switch the washing machine on again by

pressing the “On/Off” button.

• Reselect the desired programme and options.

Select the desired delay time by (repeatedly)

pressing the “Start Delay” button. Press the

“Start” button.

Verify that the appliance is switched on.

Turn on the tap and press the “Start” button.

The indicator lamp of the “Start” button stops

flashing and lights up.

Note: If there is a power interruption or if the

appliance is disconnected during the cycle, the

programme will run again from the point where it

was interrupted.

• The “End” lamp of the programme sequence

indicator lights up.

1. Press the “On/Off” button to switch off the

machine.

2. Turn the tap off.

3. Wait for the lid to unlock (about 1 minute).

Open the lid and the drum doors and unload

the machine. Leave the lid open for some time

to allow the inside of the appliance to dry

1. Switch the appliance off by pressing “On/Off”.

2. Turn the programme selector knob to the new

programme.

3. Switch the appliance on again by pressing

“On/Off”. The “Start” button flashes. If

necessary, select additional options and

different spin speed.

4. Start programme by pressing the “Start” button.

If, for any reason, you wish to interrupt the

programme for a certain time and continue it later:

1. Press the “On/Off” button.

2. After the desired pause, press again on the

“On/Off” button.

1. Switch off the appliance by pressing “On/Off”.

2. Turn the programme selector to “Drain” .

3. Switch the appliance on again by pressing

“On/Off”. The lamp of the “Start” button

flashes.

4. Press the “Start” button to start the “Drain”

programme.

START DELAY

PROGRAMME START

END OF WASH CYCLE

CHANGE THE PROGRAMME DURING

THE WASH CYCLE

PAUSE/INTERRUPT A PROGRAMME

CANCEL PROGRAMME

Whirlpool AWE 6722 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWE 6722

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info