Bedienungsanleitung Whirlpool AWE 6735 (Seite 2 von 2) (Englisch)

539841

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 300 00135

Whirlpool is a registered trademark of Whirlpool USA.

Programme

Tempe-

rature

(°C)

Load

(kg)

Water

(l)

Energy

without “Rapid”

(kWh)

Approx. Programme Duration (hrs : min)

without “Rapid” with “Rapid”

Cotton 95 5.5 55* 1.70 1:55 1:45

Cotton 60 5.5 48 1.02 2:20 1:45

Cotton 40 5.5 48 0.64 2:05 1:30

Jeans 40 4.0 41 0.58 1:44 –

Synthetics 60 3.0 50* 0.90 2:05 1:14

Synthetics 40 3.0 40 0.50 1:50 0:59

Delicates 40 1.5 50 0.55 0:45 –

Delicates 30 1.5 50 0.50 0:41 –

Daily load 40 3.0 40 0.45 1:00 –

Speed 15’ 30 3.0 30 0.15 0:15 –

Wool/Handwash 40 1.0 40 0.55 0:35 –

Wool/Handwash Cold 1.0 40 0.10 0:30 –

eCotton ** 60 5.5 48 0.83 3:20 –

eCotton ** 60 2.75 33 0.72 2:10 –

eCotton 40 5.5 48 0.65 2:00 –

eCotton ** 40 2.75 33 0.51 1:45 –

ADD DETERGENTS, CLOSE THE LID AND

SELECT THE PROGRAMME

Add detergents as indicated on the front page and as

described in the chapter “Detergent and Additives” in

your Instructions for Use.

1. Turn the programme selector to the desired

programme and temperature.

2. The display shows the programme duration and the

predefined spin speed.

3. The indication lamp next to the “Start/Pause”

button blinks.

If you do not start the programme soon after having

made your choice, the washing machine will switch off

automatically after about a quarter of an hour. Switch on

the washing machine again by turning the programme

selector back to „Off/O“ and then to the desired

programme.

SELECT ANY DESIRED OPTION

Push the button(s) of any option(s) desired - the

respective indication lights up. When the combination

of programme and additional option(s) is not possible,

the indication lights switch off automatically. Unsuitable

combinations of options are deselected automatically.

“Clean+” button

• Choose this option if you use an in-wash additive for

stain removal (powder, for example “Vanish”) - it will

optimize the additive’s efficiency to get better wash

performance and stain removal.

• Choose temperature of 30 or 40°C and use with

maximum load.

• Add an appropriate amount of in-wash additive

for stain removal (powder) to the main wash

chamber, together with your detergent (only use

powder detergent with this option). Respect the

manufacturer’s dosing instructions.

• Prolongs the programme by approx. 10 to 15 minutes.

• Appropriate for use of stain removers and bleaches

on oxygen basis. Chlorine or perborate bleaches

must not be used!

“Rapid” button

• Enables quicker washing by shortening the

programme duration.

• Recommendable for small loads or only lightly soiled

laundry.

“Prewash” button

• Only for heavily soiled loads (for example

sand, granular dirt). Increases the cycle time by

approximately 15 min.

• Do not use liquid detergent for the main wash when

activating the Prewash option.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with very

soft water, washing baby linen and helping people

with allergies.

“Rinse hold” button

• The laundry remains in the last rinse water without

progressing to the final spin cycle to avoid creasing

and prevent colours from changing.

• It is particularly useful if you want to postpone

spinning to a later time, or if you want to drain only.

• If you select “Rinse hold”, do not leave items to soak

for too long.

Note: The programme stops to “Rinse hold” at

the time the “Rinse hold” light in the programme

sequence indicator is on. The indication lamp next to

the “Start/Pause” button blinks.

Terminate the “Rinse hold” option:

• Press the “Start/Pause” button; the programme will

terminate automatically with the final spin cycle for

the present wash programme.

• If you do not wish to spin the clothes, turn the

programme selector to “Drain programme and press

the “Start/Pause” button.

“Spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is

cancelled but intermediate spin peaks remain during

the rinse. The water is drained out only.

START DELAY

The “Start delay” button allows the user to run the

machine at his convenience, for example at night when

electricity is cheaper.

• Do not use liquid detergent when activating this

function.

• Select programme, spin speed and options.

• Press the “Start delay” button several times to select

a delay time by 1 to 23 hours.

• Start the programme (see “Progremme Start”). The

indication lamp over the “Start delay” button lights

up and goes off when the programme starts.

• Once having pressed the “Start/Pause” button,

the countdown of the time delay begins. The time

delay indication on the display disappears when the

programme starts and is replaced by the remaining time.

• After the “Start/Pause” button has been pressed,

the number of hours preselected can be reduced by

pressing again the “Start delay” button.

To cancel the “Start delay”

..before you press the “Start/Pause” button:

• Turn the programme selector to another position or

press the “Reset” button.

..after having pressed the “Start/Pause” button:

• Press the “Reset” button for at least 3 second. The

start delay indicator light goes off.

PROGRAMME START

Open the tap and press the “Start/Pause” button.

The indication lamp next to the “Start/Pause” button

lights up. The programme sequence indicator shows the

current programme phase, running from left to right

through Wash, Rinse, Spin/Drain. When the programme

phase is finised, the corresponding indication goes out.

• Note: If there is a power interruption or if the

appliance is disconnected during the cycle, the

programme will run again from the point where it

was interrupted.

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with

respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer

to the default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.

The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also

“Troubleshooting Guide” in your Instructions for Use).

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

** Standard Cotton programme and basis for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.

CONSUMPTION DATA

Power consumption in off-mode 0.11 W / in left-on mode 0.11 W

“LID OPEN” INDICATION

Before starting and after end of a programme, the lamp

lights to show the the lid can be opened. As long as a

wash programme is running, the lid remains locked and

must on no account be forced open. In case you have

an urgent need to open it during a running programme,

refer to “Cancel a running programme before the end”.

FAILURE INDICATIONS

In case of any failures or irregularities, consult the

“Troubleshooting Guide” in your Instructions for Use.

“Water tap closed”

No or not sufficient inlet water.

“Service”

Failure or malfunction of an electrical component.

“Clean pump”

Waste water is not pumped out.

•

PROGRAMME END

The “Lid open” indicator lights up, and the display

shows “End”. After about a quarter of an hour, the

washing machine will switch off completely to save

energy.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open lid and drum and unload the machine.

4. Leave the lid open for some time to allow the interior

of the machine to dry.

•

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

Press the “Start/Pause” button to pause the

programme. The light blinks.

• Select the new programme, temperature, any options

and another spin speed if you want.

• Press the “Start/Pause” button again. The new

programme continues at the same position where the

previous programme was interrupted. Do not add

detergent for this programme.

CANCEL A RUNNING PROGRAMME BEFORE

THE END

The “Reset” button cancels a programme before the

end.

Press the “Reset” button for at least 3 seconds. Any

existing water is drained out before the door can be

opened.

Whirlpool AWE 6735 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWE 6735

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info