Bedienungsanleitung Whirlpool AWG 5060 (Seite 4 von 11) (Englisch)

574962

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

BEFORE USING THE APPLIANCE

1.Removing the packaging and inspection

•

After unpacking, make sure that the appliance is

undamaged. If in doubt, do not use the appliance.

Contact After-Sales Service or your local retailer.

•

Keep the packaging materials (plastic bags,

polystyrene parts, etc.) out of reach of children,

as they are potentially dangerous.

2.Remove the transport bolts

•

The appliance is fitted with transport bolts to

prevent internal damage during transport.

Before using the appliance, you must

remove the transport bolts

(see “Installation/

Remove the transport bolts”).

3.Install the appliance

•

Move the appliance without carrying it by the

worktop.

•

Install the appliance on a solid and level floor

surface, preferably in a corner of the room.

•

Make sure that all four feet are stable and resting on

the floor and then check that the appliance is

perfectly level using a spirit level (see Installation/

Adjust the feet”).

4.Water supply

•

Connect the water supply inlet hose in

accordance with the regulations of your local

water company (see “Installation/Connect the

water inlet hose”).

•

Water supply: Cold water only

•

Tap: 3/4” threaded hose

connector.

•

Pressure: 0.05-1.00 MPa

(0.5-10 bar).

5.Drain

•

Connect the drain hose to the siphon or hook it

over the edge of a sink with the “U” bend

(see “Installation/Connect the water drain hose”).

•

If the appliance is connected to a built-in drainage

system, ensure the latter is equipped with a vent

to avoid simultaneous loading and draining of

water (siphoning effect).

6.Electrical connection

•

Electrical connections must be carried out by a

qualified technician in compliance with the

manufacturer’s instructions and current standard

safety regulations.

•

Voltage information, power consumption and

electrical protection data are supplied on the

inside of the filter cover.

•

The appliance must be connected exclusively by

means of a socket with an earth connection in

accordance with current regulations. The

appliance must be earthed by law. The

manufacturer declines all liability for damage to

persons or property deriving directly or

indirectly from failure to observe the directions.

•

Do not use extension leads or multi sockets.

•

Before any maintenance on the appliance

disconnect it from the mains supply.

•

After installation, access to the mains plug or

disconnection from the mains supply must be

ensured at all times via a double-pole switch.

•

Do not operate the appliance if it has been

damaged during transport. Inform the After-Sales

Service.

•

Mains cable replacement is only to be carried out

by After-Sales Service.

•

The appliance must only be used in the

household for the prescribed uses.

30120028GB.fm Page 6 Wednesday, May 3, 2006 3:26 PM

Black process 45.0° 150.0 LPI

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AWG 5060 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWG 5060

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info