Bedienungsanleitung Whirlpool awm 1000 silver (Seite 11 von 16) (Englisch)

314441

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

What should I do when the automatic safety system detects a malfunction?

The programme is interrupted and various indicators (if available) point to the source of the fault.

Fault description table

a.Water inlet fault (no water or insufficient

water pressure)

The “Water tap closed” indicator is on and the

digital display shows “FH”. Switch off the

appliance by turning the programme selector to

the “ ” position and unplug it.

Check whether:

•

the water tap is open and the water supply

pressure is sufficient;

•

the water inlet hose is kinked;

•

the mesh filter between the tap and the hose is

clean (see “Care And Maintenance” / “Mesh filter

in water connection”);

the water supply hose is frozen up.

Connect the appliance to the electrical supply.

Reselect the desired programme and press the

“Start/Pause”

button again to continue with

the programme (do not add detergent for this

programme)

b.Draining fault

The digital display shows “FP”. Switch off the

appliance by turning the programme selector to

the “ ” position and unplug it.

Check whether:

•

the drain hose is kinked (see “Installation”);

IMPORTANT

: before draining, allow the wash

water to cool down.

•

the drain hose is frozen.

Connect the appliance to the electrical supply.

•

The pump/filter is blocked (see “Removing The

Filter” / “Draining Residual Water”).

IMPORTANT:

Make sure that the washing water

has cooled before draining.

Reselect the desired programme and press the

“Start/Pause”

button again to continue with

the programme (do not add detergent for this

programme). If the fault re-occurs, contact

After-Sales Service (See “After-Sales Service”).

c. Electrical module fault

The digital display shows “F4” to “F21” or “888”.

•

Set the programme selector to the “ ”

position, select the desired programme and

press the

“Start/Pause”

button again. The

programme will continue.

•

If the fault re-occurs, contact After-Sales

Service (See “After-Sales Service”).

d.Aquastop / Water Stop fault

An audible tone sounds. The light of the

Aquastop / Water Stop indicator goes on. The

digital display shows “FA” and the pump is

running.

The “Aquastop / Water Stop fault” may have

been triggered by:

•

too much foam.

•

a leak in the appliance, water running into the

water tank.

Switch off the appliance by turning the

programme selector to the “ ” position,

unplug the appliance and turn off the tap.

Inform After-Sales Service and describe the fault

(see “After-Sales Service”).

If the “Start/Pause” button has not been pressed

but water is still running into the machine, shut

the water intake and also inform After-Sales

Service (see “After-Sales Service”).

Small lamp lights up Digital display Fault description

“Water tap closed” “FH” “Water inlet fault”

- “FP” “Draining fault”

- from “F4” to “F21” or “888” “Electrical components fault”

“Aquastop / Water Stop” “FA” “Water Stop fault”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool awm 1000 silver Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool awm 1000 silver

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info