Bedienungsanleitung Whirlpool awm 1200 nl (Seite 13 von 15) (Englisch)

306092

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

a. Water inlet fault (no or insufficient water supply)

For models with a fault display, the “Water tap”

indicator is on or the display alternately shows

“FH”. Switch off the appliance by turning the

programme selector to the “ ” position and

unplug it.

For models with no fault display, the washing

machine stops in the appropriate step. Switch off

the appliance and unplug it.

Check whether:

• the water tap is completely open, and the water

supply pressure is sufficient;

• the water inlet hose is kinked;

• the mesh filters are blocked (see “Care and

Maintenance” / “Water Hose Mesh Filters”);

• the water inlet hose is frozen.

Reconnect the appliance to the electrical supply.

For models with a fault display, reselect the

desired programme and press the “Start/Pause”

button again to continue with the programme (do

not add detergent for this programme).

For models without a fault display continue the

programme by pressing the “On/Off” button again

(do not add detergent for this programme).

If the fault re-occurs, contact After-Sales Service

(see “After-Sales Service”).

b.Draining out fault

For models with a fault display, depending on the

model, the display shows statically or alternately

“FP”. Switch off the appliance by turning the

programme selector to the “ ” position and

unplug it.

For models with no fault display, the washing

machine stops in the appropriate step. Switch off

the appliance and unplug it.

Check whether:

• the drain hose is kinked (see “Installation

Guide”);

• the pump / filter are blocked (see “Removing the

Filter / Draining Residual Water”);

IMPORTANT: before draining, allow the wash water

to cool down.

• the drain hose is frozen.

Connect the appliance to the electrical supply.

For models with a fault display reselect the desired

programme and press the “Start/Pause” button

again to continue with the programme (do not add

detergent for this programme).

For models without a fault display continue the

programme by pressing the “On/Off” button again

(do not add detergent for this programme).

If the fault re-occurs, contact After-Sales Service

(see “After-Sales Service”).

c. Electrical module fault

For models with a fault display “F4” to “F15” are

displayed and some or all Spin Speed Selection

LEDs are flashing. Switch off the appliance. Select

a programme and press the “Start/Pause” button

once again. The programme will continue.

For models without a fault display the washing

machine stops in the appropriate step. Switch the

appliance first off, then on. The programme will

continue.

If the fault re-occurs, contact After Sales Service

(See “After-Sales Service”).

d.Water Stop fault (if available)

The “Water Stop” may have been triggered by:

1.too much foam.

2.a leak in the inlet hose or in the appliance.

In this case the pump is switched on

automatically in order to pump the water out.

For models with a fault display the light of the

“Water Stop” indication is on. The display shows

“FA” or alternately “F” and “A” and the pump is

running. Switch off the appliance by turning the

programme selector to the “ ” position, unplug

the appliance and make sure that the water tap is

closed.

For models without a fault display the washing

machine stops in the appropriate step. Switch off

the appliance, , unplug the appliance and make

sure that the water tap is closed.

Tilt the appliance forwards carefully to allow the

collected water to flow out.

Then:

1.plug in the appliance,

2.turn the water tap on (if water immediately

flows into the appliance again, without the

appliance being started, close water supply and

call After-Sales Service).

For models with a fault display reselect the desired

programme and press the “Start/Pause” button

again to continue with the programme (do not add

detergent for this programme).

For models without a fault display continue the

programme by pressing the “On/Off” button again

(do not add detergent for this programme).

If the fault re-occurs, contact After-Sales Service

(see “After-Sales Service”).

3gb05505.fm Page 14 Wednesday, July 2, 2003 12:12 PM

Black process 45.0° 100.0 LPI

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool awm 1200 nl Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool awm 1200 nl

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info