Bedienungsanleitung Whirlpool AWM 6120 (Seite 2 von 2) (Englisch)

22985

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 301 05207/A

Whirlpool is a registered trademark of Whirlpool USA.

Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized

conditions in compliance with Standard IEC 60 456. The data on the “Energy Label” refer to programme “Cotton 60°C”.

Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and

temperature, the load and the type of wash.

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains

the water out.

Add the detergent as described in the programme

table or in the chapter “Detergents and Additives”

in the booklet.

1. Turn the

programme selector knob

to the

desired programme and temperature.

2. The pilot lamp of the

“Start/Pause”

button is

flashing.

3. The programme sequence and the predefined

spin speed indication corresponding to the

selected programme lights up.

Selecting any option the indication lights up.

When the combination of programme, additional

options and temperature is not possible, the

indication lights switch off automatically.

Unsuitable combinations of options are

deselected automatically.

“Rapid Wash” button

• For quick, economical washes. Ideal for minimum

loads of lightly-soiled articles.

Note:

reduce the detergents quantity.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. The cycle time increases

approximately 15 min.

“Intensive Rinse” button

• More water and a longer time in rinse cycle is added.

• This option is particularly suitable for areas with

very soft water, washing baby linen and helps

people with allergies.

“Rinse Hold” button

• The laundry remains in the last rinse water without

progressing to the final spin cycle to avoid

creasing and prevent colours from changing.

• This option is particularly recommended for the

programme “Synthetics” or “Delicates”.

• This function is particularly useful if you want to

postpone spinning to a later time, or if you want

to drain only.

Note:

The programme stops to “Rinse Hold” at the

time the “Rinse Hold” light in the programme flow

indication is on.

CONSUMPTION DATA

Programme

Temperature

Selector

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx.

Programme

Duration

(hours : minutes)

Cotton 90 5.5 54* 1.90 2:00

Cotton 60 5.5 49 1.04 2:20

Cotton 40 5.0 44 0.60 2:05

Synthetics 60 2.5 55 0.80 1:30

Synthetics 40 2.5 55 0.60 1:20

Synthetics short 30 3.0 37 0.40 0:30

Delicates 30 1.5 60 0.50 0:45

Wool 30 1.0 60 0.30 0:40

Silk 30 1.0 45 0.30 0:40

ADD DETERGENTS, CLOSE THE DOOR AND SELECT

THE PROGRAMME

SELECT ANY DESIDERED OPTION

Terminate the “Rinse Hold” option:

• Press the “Rinse Hold” button again; the

programme will terminate automatically with the

final spin cycle for the present wash programme.

• If you do not wish to spin the clothes, turn the

programme selector knob to the “Drain”

programme and press the

“Start/Pause”

button again when flashing.

“Spin Speed Reduction” button

• Every programme has an automatic predefined

maximum spin speed.

• Press the button to set another spin speed.

• If the spin speed “

” is selected, the final spinning

is cancelled but intermediate spin peaks remain

during rinse. The water is drained out only.

Open the tap and press the

“Start/Pause”

button.

The pilot lamp of the

“Start/Pause”

button lights up.

The indicator lamps show the sequence reached in

the programme. After starting the programme, the

sequence indication runs from left to right through

Wash, Rinse, Spin.

When the sequence of the programme is finished

the corresponding lamp goes out.

The door can be opened when the “Door Open”

indication is on.

• All the lights of the programme sequence

indication are off.

1. Turn the programme selector to the

“”

position.

2. Turn the water supply tap off.

3. Open the door and unload the machine.

4. Close the tap and leave the door ajar to allow

the drum to dry out.

1. Press the

“Start/Pause”

button to pause the

programme. The light flashes.

2. Select the new programme (with temperature),

any options and another spin speed if you want.

3. Press the

“Start/Pause”

button again. The

new programme continues at the same position

where the previous programme was

interrupted. Do not add detergent for this

programme.

1. Press the

“Start/Pause”

button to pause the

programme. The light flashes.

2. Set the programme selector to “Drain”. The

spin indicators show

“0”

3. Press the

“Start/Pause”

button to start the

drain programme.

PROGRAMME START

DOOR LOCK

PROGRAMME END

CHANGE THE PROGRAMME, OPTIONS AFTER

PROGRAMME START

CANCEL A PROGRAMME BEFORE THE END

3gb05207a.fm5 Page 2 Friday, February 22, 2002 3:57 PM

Black Process Plate

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AWM 6120 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWM 6120

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info