Bedienungsanleitung Whirlpool AWM ECO 1200 (Seite 13 von 18) (Englisch)

480647

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

a. Water inlet fault (no or insufficient water

supply)

The “Water tap” indicator is on or the display

alternately shows “FH”. Switch off the appliance

by turning the programme selector to the “ ”

position and unplug it.

Check wheter:

• the water tap is completely open, and the water

supply pressure is sufficient;

• the water inlet hose is kinked;

• the mesh filters are blocked (see “Care and

Maintenance” / “Water Hose Mesh Filters”);

• the water inlet hose is frozen.

Connect the appliance to the electrical supply.

Reselect the desired programme and press the

“Start/Pause” button again to continue with the

programme (do not add detergent for this

programme)

b.Draining out fault

The display alternately shows “FP”. Switch off the

appliance by turning the programme selector to

the “ ” position and unplug it.

Check whether:

• the drain hose is kinked (see “Installation

Instructions”);

• the pump / filter are blocked (see “Removing the

Filter / Draining Residual Water”).

IMPORTANT: before draining, allow the wash

water to cool down.

• the drain hose is frozen.

Connect the appliance to the electrical supply.

Reselect the desired programme and press the

“Start/Pause” button again to continue with the

programme (do not add detergent for this

programme).

If the fault re-occurs, contact After-Sales Service

(see “After-Sales Service”).

c. Electrical module fault

The display shows “F4” to “F15”.

• Switch off the appliance. Select a programme

and press the “Start/Pause” button once again.

The programme will continue.

• If the fault re-occurs, contact After Sales Service

(See “After-Sales Service”).

d.Water Stop fault (if available)

An audible tone sounds. The light of the Water

Stop indication is on.

The display shows “FA” and the pump is running.

Switch off the appliance by turning the

programme selector to the “ ” position, unplug

the appliance and make sure that the water tap is

closed.

The “Water Stop” may have been triggered

by:

1.too much foam.

2.a leak in the inlet hose or in the appliance.

Tilt the appliance forwards carefully to allow the

collected water to flow out.

Then:

1.connect the appliance to the electrical supply,

2.open water supply to machine (if “Start/Pause”

button is not pressed, but machine begins to fill,

close water supply and call After-Sales Service),

3.reselect the desired programme and press the

“Start/Pause” button (there is no need to add

additional detergent). The programme will

continue.

If the faults occurs again, call After-Sales Service with

details about the fault (see “After-Sales Service”).

3gb05030.fm5 Page 32 Monday, September 17, 2001 3:33 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AWM ECO 1200 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWM ECO 1200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info