Bedienungsanleitung Whirlpool AWM6224 (Seite 2 von 2) (Englisch)

37974

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 301 05498

Whirlpool is a registered trademark of Whirlpool USA.

Prewash might increase programme duration. Consumption values were measured in normalized conditions in compliance

with Standard IEC 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the

water supply pressure and temperature, the load and the type of wash.

* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the

household conditions applicable at that time.

**To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the

water out.

Add the detergent as described in the programme

table or in the chapter “Detergents and Additives” in

the booklet.

1. Turn the

programme selector knob

to the

desired programme and temperature.

2. The remaining time display shows the duration of

the chosen programme (in hours and minutes)

and after taking some seconds for calculating,

the pilot lamp of the

“Start/Pause”

button is

flashing.

3. The programme sequence and the predefined

spin speed indication corresponding to the

selected programme lights up.

Selecting any option the indication lights up.

When the combination of programme, additional

options and temperature is not possible, the

indication lights switch off automatically.

Unsuitable combinations of options are

deselected automatically.

“Easy Ironing” button

• Can be used together with Cotton and Synthetics

programmes to make ironing easier.

• Increases the water quantity and the clothes are

spun very soft.

“Eco Wash” button

• The duration of the wash is extended and the

temperature reduced to save up to 40% of energy

but maintaining good washing results.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. The cycle time increases

approximately 15 min.

“Intensive Rinse” button

• More water and a longer time in rinse cycle is

added.

• This option is particularly suitable for areas with

very soft water, washing baby linen and helps

people with allergies.

CONSUMPTION DATA

Programme

Temperature

Selector

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx.

Programme

Duration

(hours : minutes)*

Cotton 95 5.0 49

1.90 2:00

Cotton 60 5.0 44 0.95 2:00

Cotton 40 4.5 44 0.60 2:05

Synthetics 60 2.5 55 0.80 1:30

Synthetics 40 2.5 55 0.60 1:20

Short 30 3.0 37 0.40 0:30

Delicates 40 1.5 60 0.60 0:45

Wool 40 1.0 60 0.30 0:40

Silk 30 1.0 45 0.30 0:40

ADD DETERGENTS, CLOSE THE DOOR AND SELECT

THE PROGRAMME

SELECT ANY DESIRED OPTION

“Rinse Hold” button

• The laundry remains in the last rinse water

without progressing to the final spin cycle to

avoid creasing and prevent colours from

changing.

• This option is particularly recommended for the

programme “Synthetics” or “Delicates”.

• This function is particularly useful if you want

to postpone spinning to a later time, or if you

want to drain only.

Note:

The programme stops to “Rinse Hold” at the

time the “Rinse Hold” light in the programme flow

indication is on.

Terminate the “Rinse Hold” option:

• Press the “Rinse Hold” button again; the

programme will terminate automatically with

the final spin cycle for the present wash

programme.

• If you do not wish to spin the clothes, turn the

programme selector knob to the “Drain”

programme and press the

“Start/Pause”

button

again when flashing.

“Spin Speed Reduction” button

• Every programme has an automatic predefined

maximum spin speed.

• Press the button to set another spin speed.

• If the spin speed “

” is selected, the final

spinning is cancelled but intermediate spin

peaks remain during rinse. The water is drained

out only.

Open the tap and press the

“Start/Pause”

button.

The pilot lamp of the

“Start/Pause”

button lights

up.

The indicator lamps show the sequence reached in

the programme. After starting the programme, the

sequence indication runs from left to right through

Wash, Rinse, Spin.

When the sequence of the programme is finished

the corresponding lamp goes out.

The door can be opened when the “Door Open”

indication is on.

• The remaining time is on “0:00” and all the

lights of the programme sequence indication

are off.

1. Turn the programme selector to the

“”

position.

2. Turn the water supply tap off.

3. Open the door and unload the machine.

4. Close the tap and leave the door ajar to allow

the drum to dry out.

1. Press the

“Start/Pause”

button to pause the

programme. The light flashes.

2. Select the new programme (with temperature),

any options and another spin speed if you

want.

3. Press the

“Start/Pause”

button again. The

new programme continues at the same position

where the previous programme was

interrupted. Do not add detergent for this

programme.

1. Press the

“Start/Pause”

button to pause the

programme. The light flashes.

2. Set the programme selector to “Drain”. The

spin indicators show

“0”

and the remaining

time shows “0:02”.

3. Press the

“Start/Pause”

button to start the

drain programme.

PROGRAMME START

DOOR LOCK

PROGRAMME END

CHANGE THE PROGRAMME, OPTIONS AFTER

PROGRAMME START

CANCEL A PROGRAMME BEFORE THE END

3gb05498.fm Page 2 Tuesday, June 24, 2003 5:48 PM

Black process 45.0° 100.0 LPI

Whirlpool AWM6224 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWM6224

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info