Bedienungsanleitung Whirlpool AWM9100 (Seite 26 von 32) (Englisch)

38275

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

TROUBLESHOOTING GUIDE

This washing machine is equipped with automatic

safety functions which detect and diagnose faults

at an early stage and react appropriately.

Often, however, the faults detected are small

enough to be solved in a matter of minutes.

For example:

The appliance will not start; no lamp lights

up.

Check whether:

•

the appliance is plugged in;

•

the wall socket is functioning correctly

(use a table lamp or similar to test);

•

the plug fuse has to be replaced (see “Electrical

Connection”);

•

a programme is selected correctly.

The appliance will not start, but the

selected programme lamp is flashing.

Check whether:

•

the appliance door is properly closed

(child lock screw);

•

open the door and close it again.

The appliance stops during the programme

and the Estimated Remaining Time display

is flashing.

Check whether:

•

another programme has been selected.

Reselect the desired programme and press the

“Start”

button, do not add detergent for this

programme;

•

The appliance safety system has been activated.

See fault description table.

Detergent and additives incorrectly washed in.

Check whether:

•

the detergent dispenser inserts are incorrectly

located (see “Care and Maintenance”);

•

enough water is being supplied. The mesh filters

in the water connection could be blocked (see

“Care and Maintenance”).

The appliance vibrates during the spin cycle.

Check whether:

•

the appliance is levelled and solidly installed on

all four feet (see “Installation”);

•

the transit bolts have been removed. Before

using the washing machine you must remove the

transit bolts (see “Installation”).

Final spin results are poor:

The appliance has an imbalance detection and

correction system. If individual heavy articles are

loaded (bathmat, bathrobe, etc.) this system may

reduce the spin speed automatically to protect the

appliance or interrupt the spin cycle altogether if

the imbalance is too great after several spin starts.

•

If the laundry is still too wet at the end of the

cycle, add other articles of laundry and repeat

the spin cycle.

•

Excessive foam formation may prevent spinning.

Ensure correct amount of detergent is used.

•

Check whether the spin speed has been reduced

to “No spin”.

What should I do when the automatic safety system detects a malfunction?

The programme is interrupted and various fault codes on the Control panel display (if available) point to

the source of the fault.

Fault description table

Digital display Fault description

“FH” “Water inlet fault”

“F02” “Draining fault”

from “F4” to “F21” “Electrical components fault”

“SUD” “Suds Routine”

7gb14811.fm Page 8 Tuesday, November 5, 2002 12:58 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AWM9100 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWM9100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info