CONSUMPTION DA T A
Cons umptio n value s were measu red in normal ized c onditi ons in compli ance w ith st andard IEC/EN 60 45 6. Cons umptio n data in the home
may vary w ith res pect t o the values in the table in re lation to the water suppl y press ure an d temp erature , the load a nd the type o f wash .
* The remain ing ti me ind icator can de viate from t he valu es in the ta ble, b ecause it tak es int o accou nt the house hold c onditio ns
ap plicab le at that ti me.
** T o redu ce the water temper ature, some cold w ater is added at th e end o f the main w ash cy cle, be fore t he pum p drain s the water out.
*** Re ference Pro gramme for En ergy L abel.
ADD DETERGENTS, CL OSE THE DOOR AND
SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“DOOR OPEN” INDICA TION
Before starting and after end of a programme, the lamp
lights to show the the door can be opened. As long
as a wash programme is running, the door remains
locked and must on no account be forced open.
In case you have an urgent need to open it during a
running programme, refer to “Cancel (Reset) a running
programme before the end”.
RED INDICA TIONS
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component. Refer to the
“T roubleshooting Guide” in your “Instructions for Use”;
if the fault persists, contact our After Sales Service.
“ W ater tap closed”
The appliance has no or insufficient water supply . Open
the water tap: if the indications still lights up, refer to the
“T roubleshooting Guide” in the Instructions for Use.
“Clean pump”
W aste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned: in the
latter case refer to the Instructions for Use (“Removing
the Filter ”).
Push the button(s) of any option(s) desired - the
respective indication lamp lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically . Unsuitable combinations of options are
deselected automatically .
“Clean+” button
• Choose this option if you use an in-wash additive for
stain removal (powder , for example “ V anish”) - it will
optimize the additive’s efficiency to get better wash
performance and stain removal.
• Selectable for programmes “
Cotton ” and “Synthetics”;
choose temperature of 30 or 40°C and use with
maximum load.
• Add an appropriate amount of in-wash additive for
stain removal (powder) to the main wash chamber ,
together with your detergent (only use powder
detergent with this option).
PROGRAMME ST ART
Open the tap and press the “Start” button. The
indication lamp next to the “Start” button lights up.
The programme sequence indicator shows the current
programme phase, running from left to right through
W ash, Rinse, Spin/Drain.
The time display shows the remaining programme
time. Due to variations in load and temperature of inlet
water , the remaining time is newly calculated in certain
programme phases. If this is the case, an animation
appears on the time display .
PROGRAMME END
• All the lights of the programme sequence indicator
are off , and the “Door open ” indication lights up.
1. T urn the programme selector to the “Off/O ”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry .
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME ST ART
1. Press the “Start/P ause” button to pause the
programme. The lamp blinks.
2. Select the new programme (with temperature), any
options and another spin speed if you want.
3. Press the “Start/P ause” button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
Th e “ Re se t” but ton c anc els a pr ogr amm e b ef ore th e e nd .
• Press the “Reset” button for at least 3 seconds;
“ rES” appears on the display . Any existing water
is drained out before the door can be opened.
Respect the manufacturer’s dosing instructions.
• Pr olong s the progr amme b y app rox. 1 0 to 15 min utes.
• Appropriate for use of stain removers and bleaches
on oxygen basis. Chlorine or perborate bleaches
must not be used!
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 15 min.
• Do not use liquid detergent for the main wash when
activating the “Prewash” option.
“Easy ironing” button
• Can be used together with “Cotton ”, “Synthetics”
and “Daily load” programmes to make ironing easier .
• Increases the water quantity and the clothes are spun
very gently .
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very
soft water , washing baby linen and helps people with
allergies.
“Rinse hold” button
• The laundry remains in the last rinse water without
pregressing to the final spin cycle to avoid creasing
and prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and
“Delicates”.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only .
• If you select “Rinse hold” do not leave items to soak
for too long.
The “Start delay ” allows to run the machine at the
consumer ’s convenience, for example at night when
electricity is cheaper .
Do not use liquid detergent when
activating “Start delay ” option.
• Select programme, temperature and options.
• Press the “Start delay ” button to select the delay
time by 1 to 23 hours.
• Press the “Start/P ause” button.
The countdown of the delay time begins; the “Start
delay ” indication lamp and the dot on the display will
keep blinking until the programme starts.
• The time delay indication disappears when the
programme starts and it is replaced by the remaining
programme time.
• Once having pressed the “Start/P ause” button, the
number of hours preselected can be reduced by
pressing again the “Start delay ” button.
T o cancel the “Start delay ”
...before you press the “Start/P ause” button:
• T urn the programme selector to another position or
press the “Reset” button.
...after having pressed the “Start/P ause” button:
• Press the “R eset” button for at least 3 seconds - the
start delay time disappears from the time display.
ST ART DELA Y
Add detergents as indicated on the front page and as
described in the chapter “Detergent and Additives” in
your Instructions for Use.
1. T urn the programme selector to the desired
programme and temperature.
2. The time display shows the duration of the chosen
programme (in hours and minutes), and the
“Start/P ause” indication lamp blinks.
3. The indication lamp of the predefined spin speed
lights up.
Note:
The programme stops to “Rinse hold” at the
time the “Rinse hold” lights in the preogramme
sequence indication is on. The indication lamp next
to the “Start” button blinks.
T erminate the “Rinse hold” option:
• Press the “Start/P ause” button; the programme
will terminate automatically with the final spin cycle
for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain ” programme
and press the “Start/P ause” button.
“ V ariable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
rinse. The water is drained out only .
5019 301 01069
Whirlpool is a registered trademark of Whirlpool USA.
Programme
T emperature
(°C)
Load
(kg)
W ater
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)*
Cotton 95 5.0 49** 1.90 2:00
Cotton *** 60 5.0 44 0.85 2:20
Cotton 40 5.0 44 0.60 2:00
Synthetics 60 2.5 50** 0.70 1:30
Synthetics 40 2.5 45 0.55 1:15
Sport 30 2.5 55 0.65 1:29
Delicates 30 1.5 50 0.50 0:45
Daily load 40 3.0 45 0.45 1:00
Quick wash 30 3.0 40 0.40 0:30
W ool
40 1.0 55 0.60 0:45
Handwash 40 1.0 45 0.60 0:40
Handwash 30 1.0 45 0.50 0:36