Bedienungsanleitung Whirlpool AWO 6626 (Seite 7 von 12) (Englisch)

539827

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

GB 7

CARE AND MAINTENANCE

Appliance exterior and control panel

•

Wash down with a soft, damp cloth; if necessary

use a neutral detergent (non abrasive). Dry with

a soft cloth.

Appliance interior

•

After each washing, leave the door open for some

time to allow the inside of the appliance to dry.

•

If you never or seldom wash your laundry at

95°C, we recommend to occasionally run a 95°C

programme without laundry, adding a small

amount of detergent, to keep the interior of the

appliance clean.

Door seal

•

Dry the door seal after each washing with an

absorbent cotton cloth; make sure that the door

seal is completely dry before closing the door of

the empty washing machine.

•

Check the condition of the door seal periodically.

Filter

•

Check and clean the filter regularly, at least two

or three times a year (see “Draining Residual

Water/Cleaning The Filter”).

Do not use flammable fluids for cleaning

the appliance.

Cleaning the detergent dispenser

Pull out the dispenser drawer until it stops. Press with your finger

on the space of the siphon being marked with “PUSH” (fig. “

”)

to release the drawer and pull it out completely.

Remove the siphon from the softener chamber by pulling it

upwards (fig. “

”).

Wash all the parts under running water.

Clean the dispenser compartment with a damp cloth.

Refit the siphon in the softener chamber by pushing it down until

it stops; then push the dispenser drawer back into the dispenser

compartment.

Water supply hose(s) (picture C, D or E - depending on model)

Check regularly for brittleness and cracks. If a supply hose shows a

damage, replace it by a new hose of the same type, available through

our After-Sales Service or your specialist dealer.

If the inlet hose of your washing machine corresponds with the model

on picture “

”, periodically check the safety valve inspection window:

if it is red, the hose’s waterstop function was triggered, and the hose

must be exchanged by a new one from our After-Sales Service or your

specialist dealer. For unscrewing the inlet hose as shown on picture

“

”, you must push down the release lever while unscrewing it.

If your supply hose has a transparent hose coating (fig. “

”),

periodically check the colour; if it intensifies locally, the hose may

have a leak and should be replaced. Contact our After-Sales Service

team or specialist dealer to obtain a replacement hose.

Cleaning the mesh filter in the water supply hose(s)

Close the tap and loosen the inlet hose on the tap.

Clean the internal mesh filter and screw the water inlet hose back

onto the tap.

Now unscrew the inlet hose on the rear of the washing machine.

Pull off the mesh filter from the washing machine connection

with universal pliers and clean it.

Refit the mesh filter and screw the inlet hose on again.

Turn on the tap and ensure that the connections are completely

water-tight.

PUSH

Safety valve

inspection

window

Release

lever

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AWO 6626 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWO 6626

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info