Bedienungsanleitung Whirlpool AWO 6646 (Seite 2 von 2) (Englisch)

539824

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 301 06661

Whirlpool is a registered trademark of Whirlpool USA

Load the laundry, close the door and add detergent as indicated

on the front page and as described in the chapter “Detergent and

Additives” in your Instructions for Use. Turn the programme

selector to the desired programme and temperature.

The display shows the programme duration and the predefined

spin speed. The “Start/Pause” indicator blinks.

Push the button of any option desired - the indicator lights up.

If the combination programme/option or option/option is not

possible, the indicator switches off automatically.

“Prewash” button

• Adds a prewash cycle to the wash programme selected;

prolongs the programme by about a quarter of an hour.

• Recommended for heavily soiled laundry (e.g. with sand or

granular dirt).

• Do not use liquid detergent for the main wash when

selecting “Prewash”.

“Rapid” button

• Enables quicker washing by shortening the programme duration.

• Recommendable for only lightly soiled laundry.

“Clean +” button

• Choose this option if you use an in-wash additive for stain

removal (powder, for example “Vanish”) - it will optimize the

additive’s efficiency to get better wash performance and

stain removal.

• Use with maximum load.

• Add an appropriate amount of in-wash additive for stain

removal (powder) to the main wash chamber, together with

your detergent (only use powder detergent with this option).

Respect the manufacturer’s dosing instructions.

• May prolong the programme by up to 15 minutes.

• Appropriate for use of stain removers and bleaches on oxygen

basis. Chlorine or perborate bleaches must not be used!

“Cold wash” button

• Saves energy used for water heating while maintaining a

good wash result.

• Recommendable for lightly soiled laundry without stains.

• Make sure that your detergent is suitable for cold wash

temperatures (15 or 20 °C).

• Mainly selectable on the lowest temperature step of the

programmes.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• Particularly suitable for areas with very soft water, washing

baby linen and helping people with allergies.

CONSUMPTION DATA

Programme Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approximate programme duration

(hrs.min)

without “Rapid” with “Rapid”

Cotton 95 6.0 59** 1.90

2:00 —

Cotton 60 6.0 49 1.02

2:20 1:35

Cotton 40 5.0 56 0.70

2:00 1:15

Jeans 40 5.0 76 0.70 2:15 1:30

Easy Care (Synthetics) 60 3.0 50** 0.80 1:35 1:14

Easy Care (Synthetics) 40 3.0 46 0.50 1:20 0:59

Delicates 40 1.5 60 0.65

0:50 —

Delicates 30 1.5 60 0.50

0:46 —

Daily load 40 3.0 41 0.50

1:00 —

Quick wash 30 3.0 41 0.30

0:30 —

Wool 40 1.0 45 0.50 0:40 —

Wool 20 1.0 45 0.10 0:35 —

EcoCotton* 60 6.0 49 0.78 4:00 —

EcoCotton* 60 3.0 37 0.70 2:30*** —

EcoCotton* 40 3.0 37 0.60 2:30 —

Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual

water supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx.

15°C through the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water

supply will lower the energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature.

Water and energy consumptions refer to the default setting of the programmes, with temperature and load as indicated in the table; selecting any options

or changing the spin speed will also change the consumption data.

The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also

“Troubleshooting Guide” in your Instructions for Use).

** To reduce the water temperature, some cold water is added at the end of the main wash cycle before the water is drained.

*** Automatic adaptation of programme duration after detection of wash load.

* Reference programmes for Energy Label.

LOAD LAUNDRY, ADD DETERGENT AND

SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

“Easy ironing” button

• Reduces creasing by an increased water quantity and a very

gentle spin.

“Rinse hold” button

• The laundry remains in the last rinse water without

progressing to the final spin cycle to avoid creasing and

prevent colours from changing.

• Particularly useful if you want to postpone spinning to a later

time, or if you want to drain only.

• The programme stops to “Rinse hold” at the time the “Rinse

hold” indicator in the programme flow bar is on. The “Start/

Pause” indicator blinks.

Terminate the “Rinse hold” option :

• Press the “Start/Pause” button ; the programme will

terminate automatically with the final spin cycle for the

present wash programme.

• If you do not wish to spin the clothes, turn the programme

selector to the “Drain” programme and press the “Start/

Pause” button to start draining.

“Spin” button

• Every programme has a predefined spin speed; press the

button if you want to set a different spin speed.

• If spin speed “0” is selected, the final spinning is cancelled

and the water is drained out only. However, intermediate

spin phases remain during rinse.

The “Start delay” allows to run the machine at the consumer’s

convenience, for example at night when electricity is cheaper. Do

not use liquid detergent when activating “Start delay”.

• Select programme, temperature and options.

• Press the “Start delay” button to select a delay time up to 23

hours.

• Press the “Start/Pause” button .

On the display, the start delay symbol and the dot between hours

and minutes blink. The countdown of the delay time begins.

• The delay time indicator disappears when the programme

starts and it is replaced by the remaining programme duration.

• Once having pressed the “Start/Pause” button , the delay

time can be changed by pressing again the “Start delay” button.

To cancel the “Start delay”

...before you press the “Start/Pause” button :

• Turn the programme selector to another position or press

the “Reset” button .

...after having pressed the “Start/Pause” button :

• Press the “Start/Pause” button - the selected start

delay disappears from the display.

Open the water tap and press the “Start/Pause” button .

The “Start/Pause” indicator lights up. The programme flow bar

shows the current programme phase, running from left to right

through Wash, Rinse, Spin/Drain.

When the laundry load is detected or the programme duration is

updated, an animation appears on the display.

Before starting and after end of a programme, the indicator lights to

show that the door can be opened. As long as a wash programme is

running, the door remains locked and must on no account be forced

open. In case you have an urgent need to open it during a running

programme, refer to “Reset a running programme before the end”.

If one of the failure indicators blinks, consult the

“Troubleshooting Guide” in your Instructions for Use.

“Water tap closed”: no or not sufficient inlet water.

“Service”: failure or malfunction of an electrical component.

“Clean pump”: waste water is not pumped out.

Spin speed on display blinks: unbalance during spinning.

• The “Door open” indicator lights up, and the display

shows “End”.

1. Turn the programme selector to the “Off/O” position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

1. Press the “Start/Pause” button to pause the

programme. The indicator blinks.

2. Select the new programme and, if you want, another spin

speed and any options.

3. Press the “Start/Pause” button again. The new

programme continues at the same position where the

previous programme was interrupted. Do not add

detergent for this programme.

The “Reset” button cancels a programme before the end.

• Press and hold the “Reset” button for a few seconds.

The water is drained. It may last some time until the door

can be opened.

START DELAY

PROGRAMME START

“DOOR OPEN” INDICATOR

FAILURE INDICATORS

PROGRAMME END

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

RESET A RUNNING PROGRAMME BEFORE

THE END

Whirlpool AWO 6646 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWO 6646

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info