5019 301 06427
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives” in
your Instructions for Use.
Close the door and turn thprogramme select
desired programme and temperature. The indication lamp
next to the
“Start (Pause)”
button blinks.
Push the button(s) of any option(s) desired - the respective
indication lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 15 min.
• Do not use liquid detergent for the main wash when
activating the “Prewash” option.
“Clean +” button
• Choose this option if you use an in-wash additive for
stain removal (powder
optimize the additive’s
performance and stain removal
• Selectable for programmes “Cotton
temperature of 30 or 40°C and use with maximum load.
• Add an appropriate amount of in-wash additive for
stain removal (powder
together with your detergent (only use powder
detergent with this option). R
manufacturer
• Prolongs the programme by approx. 10 to 15 minutes.
• Appropriate for use of stain remo
oxygen basis.
Chlorine or perborate bleaches must
not be used!
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very soft
water
“Rinse hold” button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and
prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and “Delicates”.
• It is particularly useful if you want to postpone spinning
to a later time, or if you wa
Note:
The programme stops to “Rinse hold” at the
time the “Rinse hold” light in the programme sequence
indication is on. The indication lamp next to the
“Start
(P
button blinks.
• If you select “Rinse Hold”, do
items to soak for t
T
• Press the
“Start (P
button; the programme
will terminate automatically with the final spin cycle for
the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain
and press the
“Start (P
button.
CONSUMPTION DATA
Programme
T
(°C)
Load
(kg)
Wa
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
Cotton 95 6.0 59
**
1.90 2:00
Cotton
***
60 6.0 49 1.02 2:20
Cotton 40 6.0 57 0.70 2:20
Synthetics 60 3.0 49
**
0.80 1:55
Synthetics 40 3.0 45 0.60 1:40
Delicates 30 1.5 60 0.50 0:45
Daily load 40 3.0 41 0.50 1:00
Quick wash 30 3.0 41 0.40 0:30
W 40 1.0 60 0.50 0:45
Handwash 40 1.0 45 0.50 0:40
Eco Cotton 60 6.0 49 0.78 4:00
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456.
may vary with resptable in relation to the water supply pre ssure and temperature, the load and the type of wash.
*
The remaining time indicator can deviate from the values in the table, because kes into account the household
conditions
applicable at that time.
**
T
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTIO
“
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinni
cancelled but intermediate spin peaks remain during
rinse. The water is drained out only
The “Start delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper. Do not use liquid detergent when
activating the “Start delay”.
• Select programme, temperature and options.
• Press the “S
1, 3, 6, 9 or 12 hours.
• Press the
“Start (P
button.
The “Start delay
of the delay time begins.
• When the programme starts, the start delay indi
light goes off and is replaced by the programme
sequence indication.
•A
“Start (P
button has been pressed,
the number of hours preselected can be reduced by
pressing again the “Start delay
T
...before you press the “Start (P
• T
press the
“Reset”
button.
...after having pressed the “Start (P
• Press the
“Reset”
button for at least 3 seconds - the
start delay indicator light goes off
Open the tap and press the
“Start (P
button. The
indication lamp next to the
“Start (P
button lights
up. The programme sequence indicator shows the current
programme phase, running from left to right through
Wash, Rinse, Spin/Drain.
When the programme phase is finished, the corresponding
indication goes out.
Before starting and after
lights to show that the door can be opened. As long as a
wash programme is running, the door remains locked and
must on no account be forced open. In case you have an
urgent need to open it during a running programme,
to “Cancel (Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by a
fault in an electrical component. Refer to the
“Troubleshooting Guide” in your Instructions for Use; if
the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open
the water tap; if the indication still lights up, refer to the
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain
hose is kinked or the filter must be cleaned; in the latter case
refer to the Instructions for Use (“Removing the Filter”).
• All the lights of the programme sequence indicator
are off
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the
“Start (P
button to pause the
programme. Th
2. Select the new programm
options and another spin speed if you want.
3. Press the
“Start (P
button again. The new
programme continues at the s
previous programme was interrupted. Do not add
detergent for this programme.
The
“Reset”
button cancels a programme before the end.
• Press the
“Reset”
button for at least 3 seconds. Any
existing water is drained out before the door can be
opened.
START DELAY
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICA
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
The Sensor Technology automatically adapts Programme Time, Wa
ter and Energy consumption to the size of your wash
30106427GB.fm Page 2 Monday, November 8, 2010 4:26 PM
Black process 45.0° 150.0 LPI
