5019 301 06166
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives” in
your Instructions for Use.
1. Turn the
programme selector
to the desired
programme and temperature.
2. The
time display
shows the duration of the chosen
programme (in hours and minutes), and the “Start
Pause” indication lamp is flashing.
3. The
indication lamp
of the predefined spin speed
lights up.
Push the button(s) of any option(s) desired - the respective
indication lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of option
deselected automatically.
“Eco” button
• With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption can be achieved.
“Prewash” button
• Only for heavily soiled load
granular dirt) sensible.
approximately 15 min.
“Easy ironing” button
• Can be used together with “Cotton
“Daily load” programmes to make ironing easier
• Increases the wate
very gently
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is parti
soft water
allergies.
“Rinse hold” button
• The laundry remains in the last rinse water without
progressing to the final
prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and “Delicates”.
• It is particularly useful if you want to postpone spinning
to a later time, or if y
Note:
The programme stops to “Rinse hold” at the
time the “Rinse hold
indication is on. The indication lamp next to the
“Start/
P
button flashes.
T
• Press the
“Start/P
button; the programme will
terminate automatically
present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain
and press the
“Start/P
button.
“
• Every programme
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
rinse. The water is drained out only
CONSUMPTION DATA
Pro
T
(°C)
Load
(kg)
W
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
Cotton 95 7.0 74
**
2.10 2:10
Cotton with “Eco”
***
60 7.0 54 1.19 2:10
Cotton 60 7.0 69 1.33 2:20
Cotton 40 7.0 69 0.75 2:05
Synthetics 60 3.0 46
**
0.80 1:35
Synthetics 40 3.0 42 0.40 1:20
Delicates 30 1.5 60 0.50 0:45
Daily load 40 4.0 48 0.50 1:00
Quick wash 30 4.0 48 0.25 0:30
W 40 1.0 60 0.55 0:45
Handwash 40 1.0 45 0.55 0:40
Consumption values were measured in normalized conditions in compliance with Standard 6. Consumptioe
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of w
*
The remaining time indicator can deviate from the values in the table, because it ta kes into account the household conditions
applicable at that time.
**
Tut.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTIO
The “Start Delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper.
• Select programme, temperature and options.
• Press the “Start Delay
by 1 to 23 hours;
• Press the
“Start/P
button.
The indication light next to the “Start Delay
lights up and the countdown of the delay time begins.
• The time delay in
programme starts and it is replaced by the remaining
programme time.
• Once having pressed the
“Start/P
button, the
number of hours preselected can be reduced by
pressing again the “Start Delay
T
..before you press the “Start/P
• T
press the
“Reset”
button.
..after having pressed the “Start/Pause” button:
• Press the
“Reset”
button for at least 3 seconds - the
start delay time disappears fr
Open the tap and press the
“Start/P
button. The
indication lamp next to the
“Start/P
button lights
up. The programme sequeindicator shows the current
programme phase, running from left to right through
Wash, Rinse, Spin/Drain.
The time display sremaining programme time.
Due to variations in load and temperature of inlet water,
the remaining time is newly calculated in certain
programme phases. If this is the case, an animation appears
on the time display.
Before starting and after
lights to show that the door can be opened. As long as a
wash programme is running, the door remains locked and
must on no account be forced open. In case you have an
urgent need to open it during a running programme, refer
to “Cancel (Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by a
fault in an electrical component. Refer to the
“Troubleshooting Guide” in yur Instructions for Use; if
the fault persists, contact our After Sales Service
“Water tap closed”
The appliance has no or insufficient water supply. Open
the water tap; if the indication still lights up, refer
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain
hose is kinked or the filter must be cleaned; in the latter case
refer to the Instructions for Use (“Removing the Filter”).
• All the lights of the programme sequence indicator
are off
1. Turn the programme selector to the “Off/O” position.
2. Close the water
3. Open the door and unload the machine.
4. Leave the do
1. Press the
“Start/P
button to pause the
programme. The light flashes.
2. Select the new programme (with temperature), any
options and another spin speed if you want.
3. Press the
“Start/P
button again. The new
programme continues at the s
previous programme was interrupted. Do not add
detergent for this programme.
The
“Reset”
button cancels a programme before the end.
• Press the
“Reset”
button for at least 3 seconds. Any
existing water is drained out before the door can be
opened.
START DELAY
PRO
“DOOR OPEN” INDICATION
RED INDICA
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30106166GB.fm Page 2 Friday, April 11, 2008 12:39 PM
Black process 45.0° 100.0 LPI
