Whirlpool is a registered trademark of Whirlpool USA
Load the laundry, close the door and add detergent as indicated
on the front page and as described in the chapter “Detergent and
Additives” in your Instructions for Use. Turn the programme
selector to the desired programme and temperature.
The display shows the programme duration and the predefined
spin speed. The “Start/Pause” indicator blinks.
Push the button of any option desired - the indicator lights up.
If the combination programme/option or option/option is not
possible, the indicator switches off automatically.
“Prewash” button
•Adds a prewash cycle to the wash programme selected;
prolongs the programme by about a quarter of an hour.
•Recommended for heavily soiled laundry (e.g. with sand or
granular dirt).
•Do not use liquid detergent for the main wash when
selecting “Prewash”.
“Rapid” button
•Enables quicker washing by shortening the programme duration.
•Recommendable for only lightly soiled laundry.
“Clean +” button
•Choose this option if you use an in-wash additive for stain
removal (powder, for example “Vanish”) - it will optimize the
additive’s efficiency to get better wash performance and
stain removal.
•Use with maximum load.
•Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together with
your detergent (only use powder detergent with this option).
Respect the manufacturer’s dosing instructions.
•May prolong the programme by up to 15 minutes.
•Appropriate for use of stain removers and bleaches on oxygen
basis. Chlorine or perborate bleaches must not be used!
“Cold wash” button
•Saves energy used for water heating while maintaining a
good wash result.
•Recommendable for lightly soiled laundry without stains.
•Make sure that your detergent is suitable for cold wash
temperatures (15 or 20 °C).
•Mainly selectable on the lowest temperature step of the
programmes.
“Intensive rinse” button
•More water is added and rinse cycle is prolonged.
•Particularly suitable for areas with very soft water, washing
baby linen and helping people with allergies.
“Easy ironing” button
•Reduces creasing by an increased water quantity and a very
gentle spin.
CONSUMPTION DATA
ProgrammeTemperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approximate programme duration
(hrs.min)
without “Rapid”with “Rapid”
Cotton957.074**2.20
2:30—
Cotton607.0541.19
2:201:35
Cotton407.0660.75
2:051:15
Jeans404.0520.501:301:10
Synthetics603.046**0.901:351:10
Synthetics403.0420.501:200:55
Delicates401.5600.65
0:50—
Delicates301.5600.40
0:46—
Daily load404.0480.50
1:00—
Quick wash303.0250.15
0:15—
Wool401.0450.550:40—
Woolcold1.0450.100:35—
EcoCotton*607.0540.914:00—
EcoCotton*603.5420.853:00***—
EcoCotton*403.5420.602:30—
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual
water supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx.
15°C through the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water
supply will lower the energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature.
Water and energy consumptions refer to the default setting of the programmes, with temperature and load as indicated in the table; selecting any options
or changing the spin speed will also change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
**To reduce the water temperature, some cold water is added at the end of the main wash cycle before the water is drained.
***Automatic adaptation of programme duration after detection of wash load.
*Reference programmes for Energy Label.
LOAD LAUNDRY, ADD DETERGENT AND
SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“Rinse hold” button
•The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and
prevent colours from changing.
•Particularly useful if you want to postpone spinning to a later
time, or if you want to drain only.
•The programme stops to “Rinse hold” at the time the “Rinse
hold” indicator in the programme flow bar is on. The “Start/
Pause” indicator blinks.
Terminate the “Rinse hold” option:
•Press the “Start/Pause” button ; the programme will
terminate automatically with the final spin cycle for the
present wash programme.
•If you do not wish to spin the clothes, turn the programme
selector to the “Drain” programme and press the “Start/
Pause” button to start draining.
“Spin” button
•Every programme has a predefined spin speed; press the
button if you want to set a different spin speed.
•If spin speed “0” is selected, the final spinning is cancelled
and the water is drained out only. However, intermediate
spin phases remain during rinse.
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper. Do
not use liquid detergent when activating “Start delay”.
•Select programme, temperature and options.
•Press the “Start delay” button to select a delay time up to 23
hours.
•Press the “Start/Pause” button .
On the display, the start delay symbol and the dot between hours
and minutes blink. The countdown of the delay time begins.
•The delay time indicator disappears when the programme
starts and it is replaced by the remaining programme duration.
•Once having pressed the “Start/Pause” button , the delay
time can be changed by pressing again the “Start delay” button.
To cancel the “Start delay”
...before you press the “Start/Pause” button :
•Turn the programme selector to another position or press
the “Reset” button .
...after having pressed the “Start/Pause” button :
•Press the “Start/Pause” button - the selected start
delay disappears from the display.
Open the water tap and press the “Start/Pause” button .
The “Start/Pause” indicator lights up. The programme flow bar
shows the current programme phase, running from left to right
through Wash, Rinse, Spin/Drain.
When the laundry load is detected or the programme duration is
updated, an animation appears on the display.
Before starting and after end of a programme, the indicator lights to
show that the door can be opened. As long as a wash programme is
running, the door remains locked and must on no account be forced
open. In case you have an urgent need to open it during a running
programme, refer to “Reset a running programme before the end”.
If one of the failure indicators blinks, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Water tap closed”: no or not sufficient inlet water.
“Service”: failure or malfunction of an electrical component.
“Clean pump”: waste water is not pumped out.
Spin speed on display blinks: unbalance during spinning.
•The “Door open” indicator lights up, and the display
shows “End”.
1.Turn the programme selector to the “Off/O” position.
2.Close the water tap.
3.Open the door and unload the machine.
4.Leave the door ajar to allow the drum to dry.
1.Press the “Start/Pause” button to pause the
programme. The indicator blinks.
2.Select the new programme and, if you want, another spin
speed and any options.
3.Press the “Start/Pause” button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add
detergent for this programme.
The “Reset” button cancels a programme before the end.
•Press and hold the “Reset” button for a few seconds.
The water is drained. It may last some time until the door
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Whirlpool AWO 7666 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
