Power consumption in off-mode 0.16 W / in left-on mode 0.16 W
PROGRAMME START
Open the tap and press the “Start/Pause”button.
The indication lamp next to the “Start/Pause”button lights
up. The programme sequence indicator shows the current
programme phase, running from left to right through
Wash, Rinse, Spin/Drain.
When the laundry load is detected or the programme
duration is updated, the display shows an animation.
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp
lights to show the door can be opened. As long as a wash
programme is running, the door remains locked and must
not be forced open. In case you have an urgent need
to open it during a running programme, refer to “Cancel
(Reset) a running programme before the end”.
FAILURE INDICATIONS
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Water tap closed”: no or not sufficient inlet water.
”Service”: failure or malfunction of an electrical
component.
”Clean pump”: waste water is not pumped out.
Spin speed on display blinks : unbalance during
spinning.
PROGRAMME END
The “Door open” indicator lights up, and the display shows
“End”. After about a quarter of an hour, the washing
machine will switch off completely to save energy.
1. Turn the programme selector to the “O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
Press the “Start/Pause” button to pause the
programme. The light blinks.
2. Select the new programme, temperature, any options
and another spin speed if you want.
3. Press the “Start/Pause” button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not add
detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before the end.
•Press and hold the “Reset” button for a few seconds.
Any existing water is drained out. It may last some time
until the door can be opened..
• Make sure that your detergent is suitable for cold wash
temperatures (15 or 20 °C).
• Mainly selectable on the lowest temperature step of
the programmes
“Rapid” button
• Enables quicker washing by shortening the programme
duration.
• Recommendable for only lightly soiled laundry.
• Not selectable for Cotton 95°C.
“Clean+” button
• Choose this option if you use an in-wash additive for
stain removal (powder, for example “Vanish”) - it will
optimize the additive’s efficiency to get better wash
performance and stain removal.
• Use with the maximum load.
• Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together
with your detergent (only use powder detergent with
this option). Respect the manufacturer’s dosing
instructions.
• May prolong the programme by up to 15 minutes
• Appropriate for use of stain removers and bleaches on
oxygen basis. Chlorine or perborate bleaches must
not be used!
“Prewash” button
•Adds a prewash cycle to the wash programme
selected; prolongs the programme by about a quarter
of an hour.
• Recommended for heavily soiled laundry (e.g. with
sand or granular dirt).
•Do not use liquid detergent for the main wash when
activating the “Prewash” option.
“Intensive rinse” button
•More water is added and rinse cycle is prolonged.
•This option is particularly suitable for areas with very
soft water, washing baby linen and helps people
with allergies.
“Easy ironing” button
•Reduces creasing by an increased water quantity and
a very gentle spin.
“Rinse hold” button
•The laundry remains in the last rinse water without
pregressing to the final spin cycle to avoid creasing
and prevent colours from changing.
•It is particularly useful if you want to postpone spinning
to a later time, or if you want to drain only.
•The programme stops to “Rinse hold” at the time the
“Rinse hold” lights in the preogramme sequence
indication is on. The “Start/Pause” indicator blinks.
Terminate the “Rinse hold” option:
•Press the “Start/Pause” button; the programme will
terminate automatically with the final spin cycle for the
present wash programme.
•If you do not wish to spin the clothes, turn the
programme selector to the “Drain” programme and
press the “Start/Pause” button.
“Spin” button
•Every programme has a predefined spin speed.
•Press the button to set different spin speed.
•If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
rinse. The water is drained out only.
START DELAY
The “Start delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper. Do not use liquid detergent when
activating “Start delay” option.
•Select programme, temperature and options.
•Press the “Start delay” button to select the desired
delay time up to 23 hours.
•Press the “Start/Pause” button. On the display, the
start delay symbol and the dot between hours and
minutes blink. The countdown of the delay time begins.
•The time delay indication disappears when the
programme starts and it is replaced by the remaining
programme time.
•Once having pressed the “Start/Pause” button, the
delay time can be reduced by pressing again the “Start
delay” button.
To cancel the “Start delay”
...before you press the “Start/Pause” button:
• Turn the programme selector to another position or
press the “Reset” button.
...after having pressed the “Start/Pause” button:
• Press the “Start/Pause” button - the start delay time
disappears from the time display.
LOAD LAUNDRY, ADD DETERGENTS AND SELECT
THE PROGRAMME
Load the laundry, close the door and add detergents
as indicated on the front page and as described in the
chapter “Detergent and Additives” in your Instructions
for Use. Turn the programme selector to the desired
programme and temperature. The display shows the
programme duration and the predefined spin speed. The
indication lamp next to the “Start/Pause” button blinks.
If you do not start the programme soon after having
made your choice, the washing machine will switch off
automatically after about a quarter of an hour. To switch
the washing machine on again, turn the programme
selector to “O” and afterwards to the desired programme
again.
SELECT ANY DESIRED OPTION
Push the button of any option desired - the respective
indication lamp lights up. If the combination of programme
and additional option(s) is not possible, the indication
lights switch off automatically.
“Cold wash” button
• Saves energy used for water heating while maintaining
good wash result.
• Recommendable for lightly soiled laundry without
stains.
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water
supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15°C through
the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply will lower the
energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions refer to the default
setting of the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption
data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
Approximate remaining moisture content (%). After programme and spinning with maximum selectable spin speed, in default programme setting.
* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Automatic adaptation of programme duration after detection of wash load.
- the sensor technology adapts water, energy and programme duration to the size of your wash load.
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Whirlpool AWO 8568 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
