5019 301 01028
Programme
T
(°C)
Load
(kg)
W
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)*
Cotton 95 6.0 59** 1.90 2:00
Cotton with “Eco” *** 60 6.0 49 1.14 2:20
Cotton 40 5.0 56 0.70 2:00
Synthetics 60 2.5 50** 0.80 1:35
Synthetics 40 2.5 46 0.50 1:20
Delicates 30 1.5 60 0.50 0:45
Daily load 40 3.0 41 0.50 1:00
Quick wash 30 3.0 41 0.40 0:30
W 40 1.0 60 0.50 0:45
Handwash 40 1.0 45 0.50 0:40
Handwash 30 1.0 45 0.40 0:36
Add detergents as indicated on the front page and as
described in the chapter “Detergent and Additives” in
your Instructions for Use.
1. Tprogramme selector to the desired
programme and temperature.
2. The time display shows the duration of the chosen
programme (in hours and minutes), and the
“Start/P indication lamp is flashing.
3. The indication lamp of the predefined spin speed
lights up.
CONSUMPTION DA
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the
home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type
of wash.
* The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions
applicable at the time.
**
T
*** Reference P
ADD DETERGENTS, CL
SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the
respective indication lamp lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically
deselected automatically
“Eco” button
• With
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
“Prewash” button
• Only
granular dirt) sensible. Increases the cycle time by
approximately 15 min.
• Do
activating the Prewash option.
Whirlpool is a registered trademark of Whirlpool USA.
“Easy ironing” button
• Can
and “Daily load” programmes to make ironing easier
• Increases
spun
“Cold wash” button
• With
• Suitable
temperature recomendation of max. 30ºC on the
care label.
• Selectable
step of each programme.
“Rinse hold” button
• The
pregressing to the final spin cycle to avoid creasing
and prevent colours from changing.
• This
programmes “Synthetics”, “Daily load” and
“Delicates”.
• It
spinning to a later time, or if you want to drain only
• If
for too long.
Note: The programme stops to “Rinse hold” at the
time the “Rinse hold” lights in the preogramme
sequence indication is on. The indication lamp next
to the “Start/P button flashes.
T
• P“Start/P button; the programme
will terminate automatically with the final spin cycle
for the present wash programme.
“DOOR OPEN” INDICA
Before starting and after end of a programme, the lamp
lights to show the the door can be opened. As long
as a wash programme is running, the door remains
locked and must on no account be forced open.
In case you have an urgent need to open it during a
running programme, refer to “Cancel (Reset) a running
programme before the end”.
RED INDICA
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component. Refer to the
“T
if the fault persists, contact our After Sales Service.
“
The appliance has no or insufficient water supply
the water tap: if the indications still lights up, refer to
the
“T
“Clean pump”
W
drain hose is kinked or the filter must be cleaned: in the
latter case refer to the Instructions for Use (“Removing
the Filter
PROGRAMME ST
Open the tap and press the “Start/Pbutton.
The indication lamp next to the “Start/Pbutton
lights up. The programme sequence indicator shows
the current programme phase, running from left to
right through W
The time display shows the remaining programme
time. Due to variations in load and temperature of inlet
water
programme phases. If this is the case, an animation
appears on the time display
PROGRAMME END
• All
are off
1. T
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME ST
1. Press the “Start/Pbutton to pause the
programme. The light flashes.
2. Select the new programme (with temperature), any
options and another spin speed if you want.
3. Press the “Start/Pbutton again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before the
end.
• P“Reset” button for at least 3 seconds;
“
is drained out before the door can be opened.
• If
programme selector knob to the “Drain
and press the “Start/P button.
“
• Every
• P
• If
cancelled but intermediate spin peaks remain during
the rinse. The water is drained out only
The “Start Delay
consumer
electricity is cheaper
activating “Start delay
• Select
• P
time by 1 to 23 hours.
• P“Start/P button.
The countdown of the delay time begins; the “Start
delay
keep blinking until the programme starts.
• The
programme starts and it is replaced by the remaining
programme time.
• Once “Start/Pause” button, the
number of hours preselected can be reduced by
pressing again the “Start delay
T
..before you press the “Start/P
• T
press the “Reset” button.
..after having pressed the “Start/P
• P
start delay time disappears from the time display.
ST
