5019 301 05609
Whirlpool is a registered trademark of Whirlpool USA
Add the detergents as described in the programme
table or in the chapter “Detergents and Additives”
in the booklet.
1. Turn the
programme selector kn
to the
desired programme.
2. The remaining time display shows the duration
of the chosen programme (in hours a
minutes) and the indication of the
“Start/
Pause”
button is flashing.
3. The programme sequence and
spin speed indication corresponding to the
selected programme lights up.
The recommended temperatur
indicator) can be atered by pressing “
+
/-” button
Selecting any option the indication lights up.
When the combination of programme, additional
options and temperature is not possible, the indication
lights switch off automatically. Unsuitable
combinations of options are deselected automatically.
“Easy Ironing” button
• C
and “Daily
• I
spun very soft.
“Eco plus” button
• W
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumptio
“Pre
• O
granular dirt) sensible. The cycle time increases
approximately 15 min.
“Intensive Rins
• More water and a longer time in rinse cycle is added.
• T
very soft water
people with allergies.
“Rinse Hold” button
• T
without progressing to the final spin cycle to avoid
creasing and prevent colou
• T
programme “Synthetics”, “Dai
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only
Note:
The programme stops to “Rinse Hold” at
the time the “Rinse Hold” light in the programme
sequence indication is on.
T
• Press the “Rinse Hold” button again; the
programme will terminate auto
final spin cycle for the present wash programme.
CONSUMPTION DATA
Programme
T
Selec
(°C)
Load
(kg)
Wa
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)*
Cotton 95 6.0 54** 1.90 2:00
Cotton 60 6.0 49 1.14 2:20
Cotton with “Eco plus”*** 60 6.0 49 1.02 2:30
Cotton 40 5.0 44 0.60 2:05
Synthetics 60 2.5 55 0.80 1:30
Synthetics 40 2.5 55 0.60 1:20
Daily 40 3.0 45 0.50 1:00
Superrapid 30 3.0 37 0.40 0:30
Delicates 30 1.5 60 0.50 0:45
W 30 1 60 0.30 0:40
Handwash 30 1.0 45 0.30 0:40
Prewaslues were measured in normalized conditions in compliance
with Standard IEC/EN 60 456. Consumption data in the
water supply pressure and temperate, the load and the typ
* The remaining time indicato
conditions applicable at that time.
** T
water out.
*** Reference Programme for Energy Label
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
• If you do not wish to spin the clothes, turn the
programme selector knob counterclockwise to
the “Drain
“Start/P
button again when the indication
next to it is flashing.
“Spin Speed” button
• Every programme has an automatic predefined
maximum
• Press the button to set another spin speed.
• If the spin speed “0” is sele
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only
The “Start Delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is c
• Select programme, temperature and options.
• Press the “Star
time by 1 to 23 hours;
•P
“Start/P
button.
The indication next to the “Start Delay
lights up and goes off when the programme starts.
• The time delay indication disappears when the
programme starts and it is replaced by the
remaining time.
• The number of hours preselected can later be
reduced pressing again the “Start Delay
T
..before you press the “Start/P
• T
“
Off
/0”
position.
• R
press
“Start/P
button to start the programme.
..after having pressed the “Start/Pause” button:
• Press the “R
the start delay time disappears from the
remaining time indication,
• then either start th
pressing the
“Start/P
button twice
• or turn the programme selector knob to the
“
Open the tap and
“Start/Pause”
button. The
indication next to the
“Start/Pause”
button lights up.
The indi
programme. After starting the programme, the
sequence indication runs from left to right through
Wash, Rinse, Spin.
When the sequence of th
the corresponding in
“Water Tap Closed”
The appliance has no or insufficient water supply.
Open the water tap; if the indication still ligh
refer to the “Troubles
Instructions for Use.
“Clean Pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter
the latter case refer to the Instructions for Use
(“Removing the Filter”).
“Door Locked”
As long as a washing programme is running, the
lamp lights up to show that the door cannot be
opened. When the indication goes off, the
be opened again.
“Water Stop”
Lighting up of the water stop indication can be
caused by a leak in the appliance or hose. Please
refer to the “Troubles
Instructions for Use.
• T
lights of the programme sequence indication
are off.
1. Turn the programme selector to the
“
Off
/0”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry out.
1. Press the
“Start/Pause”
button to pause the
programme. The light flashes.
2. Select the new programme (with temper
any options and another spin speed if you want.
3. Press the
“Start/Pause”
button again. The
new programme continues at the same position
where the previous programme wa
interrupted. Do not add detergent for this
programme.
The
“Reset”
button cancels a programme before
the end.
•P
“Reset”
button for at least 3 seconds.
Any existing water is drained out before the
door can be opened.
START DELAY
PROGRAMME S
RED INDICA
PROGRAMME END
CHANGE THE PROGRAMME,
TEMPERATURE, OPTIONS AFTER
PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
3gb05609.fm Page
Black process 45.0° 100.
