Bedienungsanleitung Whirlpool AWO 9487 Green (Seite 2 von 2) (Englisch)

488738

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 301 06523

Whirlpool is a registered trademark of Whirlpool USA

Add detergent as indicated on the front page and as described in

the chapter “Detergent and Additives” in your Instructions for Use.

Turn the programme selector to the desired programme; the light

of the “Start/Pause” button blinks. The temperature and

spin speed indicated on the display can be altered by pressing the

“Temperature” button or the “Spin” button .

When the combination of programme and additional option(s) is

not possible, the indication switch off automatically. Unsuitable

combinations of options are deselected automatically. For certain

programmes, an option may already be preset; if you want you can

deselect it.

“Clean +” button

• Choose this option if you use an in-wash additive for stain removal

(powder, for example “Vanish”) - it will optimize the additive’s

efficiency to get better wash performance and stain removal.

• Use with maximum load.

• Add an appropriate amount of in-wash additive for stain

removal (powder) to the main wash chamber, together with

your detergent (only use powder detergent with this option).

Respect the manufacturer’s dosing instructions.

• May prolong the programme by up to 15 minutes.

• Appropriate for use of stain removers and bleaches on oxygen

basis. Chlorine or perborate bleaches must not be used!

“Rapid” button

• Enables quicker washing by shortening the programme duration.

• Recommendable for only lightly soiled laundry.

“Prewash” button

• Only for heavily soiled loads (for example sand, granular dirt).

Increases the cycle time by approximately 15 min.

• Do not use liquid detergent for the main wash when activating

the “Prewash” option.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with very soft

water or for washing baby linen, and helps people with

allergies.

“Soil level” button

• Adapts the programme duration to the soil level of your

laundry. Also influences the detergent quantity

recommendation when using the “Dosing Aid” button.

= lightly soiled - = normally soiled - = heavily soiled

Not all soil levels are selectable for each programme.

“Spin” button (incl. “Rinse Hold” )

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If you select spin speed “0”, the final spinning is cancelled and

the water is drained out only. However, intermediate spin

phases remain during the rinse.

• If you select “Rinse hold” , the laundry remains in the last

rinse water without progressing to the final spin cycle, to avoid

creasing and prevent colours from changing. To activate the

“Rinse hold”, press the “Spin” button repeatedly until the

“Rinse hold” symbol on the display lights up.

- The wash programme stops to “Rinse hold” when the

“Rinse hold” light in the programme sequence

indicator is on; the light of “Start/Pause” button blinks.

- To terminate the “Rinse hold” by draining the water,

without any spinning, press the “Start/Pause” button.

- To terminate the “Rinse hold” by spinning the laundry, press

the “Spin” button to select the desired spin speed and then

“Start/Pause” to start the spin cycle.

- Do not leave the laundry to soak for too long in the “Rinse

hold”.

CONSUMPTION DATA

Programme

Te m p e r a t u r e

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme Duration

(hours : minutes)

without “Rapid” with “Rapid”

Mixed 40 4.0 45 0.50 1:00 —

Cotton 95 7.0 74** 2.10 2:10 —

Cotton* 60 7.0 54 0.91 4:00 2:30

Cotton* 60 3.5 40 0.85 3:00

Cotton 40 7.0 69 0.80 3:15 2:15

Cotton* 40 3.5 40 0.65 3:00

Synthetics 60 3.0 50** 0.80 1:35 1:14

Synthetics 40 3.0 46 0.50 1:20 0:59

Delicates 30 1.5 60 0.50 0:45 —

Wool/Handwash 40 1.0 45 0.50 0:40

White 40 7.0 69 0.80 3:30 —

Light colours 40 4.5 65 0.50 1:20 —

Dark 40 4.5 45 0.60 1:40 1:15

SuperEco 60 7.0 69 0.84 4:00 —

AquaEco 40 3.0 19 0.45 1:00 —

Speed 15 30 3.0 30 0.20 0:15 —

Jeans 40 4.5 60** 0.60 1:30 1:15

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with

respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. Water and energy consumption refer

to the default setting of the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change

the consumption data.

The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also

“Troubleshooting Guide” in your Instructions for Use).

* Reference programmes for Energy Label.

** To reduce the water temperature, some cold water is added at the end of the main wash cycle before the water is drained.

*** Automatic adaptation of programme duration after detection of wash load.

***

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

The “Start delay” allows to run the machine at the consumer’s

convenience, for example at night when electricity is cheaper.

• Select programme, temperature, spin speed and options.

• Press the Start delay button to select a delay time up to 23

hours.

• Press the “Start/Pause” button .

The countdown of the delay time begins; the start delay

symbol and the colon between hours and minutes blink.

• The time delay indication disappears when the programme

starts and it is replaced by the remaining programme time.

• If you use the “Dosing Aid” button: select the delay time

BEFORE pressing the “Dosing Aid” button. The countdown

of the selected delay time begins after having pressed the

“Start/Pause” button for the second time (see separate

Instructions for Use concerning the “Dosing Aid”).

To cancel the “Start delay”

...before you press the “Start/Pause” button:

• Press the “Reset/Drain” button , or set the start delay

time to “0:00” - the delay time disappears after a few seconds.

...after having started the programme:

- Press the “Start/Pause” button - the delay time

disappears from the display. Press “Start/Pause” again if

you want to start the selected programme immediately.

With the “Dosing Aid” button, you can make your washing machine

indicate you the recommended detergent quantity for your wash

load, depending on the soil level selected and the size of the load.

• Helps to save detergent and protect the environment and also

sensitive skin by avoiding detergent overdosing.

• Before you use this function, you must adapt the washing

machine to the dosing amounts which are recommended for

the detergents you use. Also check if your region’s water

hardness corresponds with the water hardness level “soft” of

your washing machine - if not adapt it.

• Select programme, options and start delay BEFORE using the

“Dosing Aid” button.

For any details, refer to the separate “Dosing Aid” Instructions for

Use.

Before starting and after end of a programme, the lamp lights to

show that the door can be opened. As long as a wash programme is

running, the door remains locked and must on no account be forced

open. In case you have an urgent need to open it during a running

programme, refer to “Reset a running programme before the end”.

Open the tap and press the “Start/Pause” button . The

indication lamp next to the “Start/Pause” button lights up.

The programme sequence indicator shows the current programme

phase, running from left to right through Wash, Rinse, Drain/Spin.

Activating the child lock prevents children from starting a wash

cycle or changing the settings of a running programme. The child

lock cannot be activated or deactivated when the programme

selector is in the “Off/O” position. To activate the child lock:

• Turn the programme selector to a programme position, or run

a programme as usual.

• Press the 2 buttons marked with the key symbol

simultaneously for at least 3 seconds. A key-like symbol will

shortly appear on the display to indicate that the child lock is

active.

Any time you try to change a programme setting with active child

lock, the display will briefly show the key-like symbol. The

programme setting cannot be changed anymore. The only change

possible is to switch the washer off by turning the programme

selector to the “Off/O” position. To deactivate the child lock:

• Press again the 2 buttons marked with the key symbol

simultaneously for at least 3 seconds.

In case of any failures or irregularities, consult the

“Troubleshooting Guide” in your Instructions for Use.

“Service”

Lighting up of the “Service” indication can be caused by a fault in an

electrical component.

“Water tap closed”

The washing machine has no or insufficient water supply; the water

tap might be closed or the water inlet hose kinked.

“Clean pump”

Waste water is not pumped out. The drain hose may be kinked or

the filter must be cleaned (see “Cleaning the filter” in your

Instructions for Use).

• All the lights of the programme sequence indicator are off

and the “Door open” indication lights up.

1. Turn the programme selector to the “Off/O” position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

The symbol will light up at the end of the programme if you used

too much detergent. Use less detergent next time. If the symbol

lights up and the display shows “Fod”, too much foam interrupted

the wash process; refer to the “Troubleshooting Guide” in your

Instructions for Use.

1. Press the “Start/Pause”

button to pause the

programme. The light blinks.

2. Select the new programme, temperature, any options and

another spin speed if you want.

3. Press the “Start/Pause” button again. The new

programme continues at the same position where the

previous programme was interrupted. Do not add detergent

for this programme.

The “Reset/Drain” button cancels a programme before

the end.

•Press and hold the “Reset/Drain” button for a few

seconds; an animation appears on the display. The water is

drained out; it may last some time until you can open the

door.

SET A START DELAY

DETERGENT DOSING

RECOMMENDATION

“DOOR OPEN” INDICATION

PROGRAMME START

CHILD LOCK

FAILURE INDICATIONS

PROGRAMME END

DETERGENT OVERDOSAGE

INDICATION

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

RESET A RUNNING PROGRAMME BEFORE

THE END

30106523GB.fm Page 2 Monday, July 11, 2011 2:37 PM

Black process 45,0° 150,0 LPI

Whirlpool AWO 9487 Green Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWO 9487 Green

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info