Bedienungsanleitung Whirlpool AWO-C 81400 (Seite 2 von 2) (Englisch)

641526

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

without “Rapid”

Approx. programme duration

(hours : minutes)

without “Rapid” with “Rapid”

Mixed 40 4,0 48 0,50 1:00 - 55

Cotton 95 8,0 82** 2,50 2:30 -

55Cotton 60 8,0 59 1,36 2:20 1:35

Cotton 40 8,0 75 1,00 2:20 1:15

Synthetics 60 3,0 48** 1,05 2:05 1:12

Synthetics 40 3,0 44 0,60 1:50 0:57

Delicates 40 1,5 60 0,65 0:50 -

Delicates 30 1,5 60 0,40 0:46 -

Wool/Handwash 40 1,0 45 0,55 0:40 -

Jeans 40 4,0 52 0,50 1:30 1:10

White 40 8,0 77 0,85 2:20 -

Light colours 40 4,0 60 0,45 1:20 -

Dark 40 4,0 40 0,55 1:40 1:15

Speed 15´ 30 3,0 25 0,15 0:15 -

AquaEco 40 3,0 19 0,45 1:00 -

Cotton

60°

60 8,0 54 0,98 3:50 -

Cotton

60°

60 4,0 40 0,75 3:15 *** -

Cotton

40°

40 4,0 45 0,62 3:00 *** -

Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water

supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15°C through

the cold ﬁll valve as well as the hot ﬁll valve (if available). If your washing machine has a hot ﬁll valve, connection of this valve to hot water supply will lower the

energy consumption by reduced heating times, depending on the individual hot ﬁll inlet water temperature. Water and energy consumptions refer to the default

setting of the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption

data.

The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also

“Troubleshooting Guide” in your Instructions for Use).

Approximate remaining moisture content (%). After programme and spinning with maximum selectable spin speed, in default programme setting.

* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.

** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

*** Automatic adaptation of programme duration after detection of wash load

ADD DETERGENTS, CLOSE THE DOOR AND

SELECT THE PROGRAMME

Load the laundry, close the door and turn the programme selector

to the desired programme; the “Start/Pause” indicator blinks.

The temperature and spin speed shown on the display can be

altered by pressing the “Temperature” button or the “Spin” button.

If you do not use the “Dosing Aid”, add detergent now.

Your washing machine is designed to save energy. After the

end of a programme, or when a programme is selected but

not yet started, the washing machine will therefore switch off

automatically after about a quarter of an hour. To switch the

washing machine on again, turn the programme selector to “O”

and afterwards to the desired programme again.

SELECT ANY DESIRED OPTION

When the combination of programme and additional option(s) is

not possible, the indication switch off automatically. Unsuitable

combinations of options are deselected automatically.

“Colours 15°” button

• Saves energy used for water heating while maintaining a good

wash result.

• Supports colour maintenance when washing coloured laundry.

• Recommendable for lightly soiled laundry without stains.

• Make sure that your detergent is suitable for cold wash

temperatures (15 or 20°C).

• Not selectable for Cotton 70 - 95°C.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with very soft

water, washing baby linen and helps people with allergies.

“Rapid” button

• Enables quicker washing by shortening the programme

duration.

• Recommendable for only lightly soiled laundry.

• Not selectable for Cotton 70 - 95°C.

“Prewash” button

• Adds a prewash cycle to the wash programme selected;

prolongs the programme by about a quarter of an hour.

• Recommended for heavily soiled laundry (e.g. with sand or

granular dirt).

• Do not use liquid detergent for the main wash when activating

the “Prewash” option.

“Soil level” button

• Adapts the programme duration to the soil level of

your laundry. Also inﬂuences the detergent quantity

recommendation when using the “Dosing Aid” button.

= lightly soiled - = normally soiled - = heavily soiled

Not all soil levels are selectable for each programme.

“Spin” button (incl. “Rinse hold”)

• Every programme has a predeﬁned spin speed.

• Press the button to set another spin speed.

• If you select spin speed “0”, the ﬁnal spinning is cancelled

and the water is drained out only. However, intermediate spin

phases remain during the rinse.

• If you select “Rinse hold”, the laundry remains in the last

rinse water without progressing to the ﬁnal spin cycle, to

avoid creasing and prevent colours from changing. To activate

the “Rinse hold”, press the “Spin” button repeatedly until the

“Rinse hold” symbol on the display lights up.

• The wash programme stops to “Rinse hold” when the “Rinse

hold” symbol on the display blinks; the light of “Start/Pause”

button also blinks.

- To terminate the „Rinse hold“ by spinning the laundry, press

“Start/Pause” - the laundry will be spun with the default

spin speed. You can also select another spin speed with the

„Spin“ button before you start the spin cycle by pressing

“Start/Pause”.

- To terminate the „Rinse hold“ by draining the water without

- the sensor technology adapts water, energy and programme duration to the size of your wash load.

PROGRAMME START

Open the tap and press the “Start/Pause” button . The indicator

next to the “Start/Pause” button lights up.

CHILD LOCK

Activating the child lock prevents children from starting a wash

cycle or changing the settings of a running programme. The child

lock cannot be activated or deactivated when the programme

selector is in the “O” position. To activate the child lock:

• Turn the programme selector to a programme position, or run

a programme as usual.

• Press the 2 buttons marked with the key symbol

simultaneously for at least 3 seconds. A key-like symbol will

shortly appear on the display to indicate that the child lock is

active.

Any time you try to change a programme setting with active

child lock, the display will brieﬂy show the key-like symbol. The

programme setting cannot be changed anymore. The only change

possible is to switch the washer off by turning the programme

selector to the “O” position.

To deactivate the child lock:

• Press again the 2 buttons marked with the key symbol simul-

taneously for at least 3 seconds.

FAILURE INDICATION

In case of any failures or irregularities, consult the

“Troubleshooting Guide” in your Instructions for Use.

“Water tap closed”: no or not sufﬁcient inlet water.

”Service”: failure or malfunction of an electrical component.

”Clean pump”: waste water is not pumped out.

Spin speed on display blinks: unbalance during spinning.

PROGRAMME END

The “Door open” indicator lights up, and the display shows “End”.

After about a quarter of an hour, the washing machine will switch

off completely to save energy.

1. Turn the programme selector to the “O” position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

DETERGENT OVERDOSAGE INDICATION

The symbol will light up at the end of the programme if you used

too much detergent. Use less detergent next time. If the symbol

lights up and the display shows “Fod”, too much foam interrupted

the wash process; refer to the “Troubleshooting Guide” in your

Instructions for Use.

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

Press the “Start/Pause” button to pause the programme. The

light blinks.

2. Select the new programme, temperature, any options and

another spin speed if you want.

3. Press the “Start/Pause” button again. The new programme

continues at the same position where the previous programme

was interrupted. Do not add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME

BEFORE THE END

The “Reset/Drain” button cancels a programme before the end.

• Press and hold the “Reset/Drain” button for a few seconds; an

animation appears on the display. The water is drained out; it

may last some time until you can open the door.

CONSUMPTION DATA

Power consumption in off-mode 0,16 W / in left-on mode 0,16 W

spinning, press the „Spin“ button until spin speed „0“ appears

on the display; then press “Start/Pause” to start the draining.

- Do not leave the laundry to soak for too long in the “Rinse

hold” (especially silk).

SET CYCLE END

With this function you can postpone your programme to complete

at a later time: press the button to select in how many hours

the programme shall be ﬁnished. Thus, it allows you to have

your laundry ready at a particular time and to proﬁt from more

favorable energy rates during the night, for example. Do not use

liquid detergent when activating “Cycle end” option.

• The time until the “Cycle end” can be selected in full hour time

segments (1 to 24 h). When you press the button, the shortest

possible time will be displayed; keep on pressing the button to

loop through all the available times. To remove it again, keep

on pressing the button until you see the value “0:00”.

• When you have selected the desired time until the “Cycle

end”, press “Start/Pause” - the countdown will begin.

• During the countdown, you can still modify the programme

setting (select or deselect options, change spin speed etc.).

If the modiﬁcations prolong the programme duration so that

it overruns the originally set time until the “Cycle end”, the

programme will start immediately.

• Sometimes the programme may ﬁnish before the selected

time until the “Cycle end” has expired (e.g. for small loads).

In this case, the washing machine will tumble the laundry

regularly to keep it fresh, until the selected “Cycle end”

time has expired. During tumbling, the display will show an

animation. The tumbling phase can be stopped at any time

either by pressing any button or by rotating the programme

selector; the animation will stop and the door will unlock in

about 1 minute as indicated on the display.

DETERGENT DOSING RECOMMENDATION

With the “Dosing Aid” button, you can make your washing

machine indicate you the recommended detergent quantity for

your wash load, depending on the soil level selected and the size

of the load.

• Helps to save detergent and protect the environment and also

sensitive skin by avoiding detergent overdosing.

• Before you use this function, you must adapt the washing

machine to the dosing amounts which are recommended

for the detergents you use. Also check if your region’s water

hardness corresponds with the water hardness level “soft” of

your washing machine - if not adapt it.

• Select programme, options and cycle end BEFORE using the

“Dosing Aid” button.

For any details, refer to the separate “Dosing Aid” Instructions for

Use.

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp lights to

show the the door can be opened. As long as a wash programme

is running, the door remains locked and must on no account be

forced open. In case you have an urgent need to open it during a

running programme, refer to “Reset” a running programme before

the end”.

ECO MONITOR

The „Eco monitor“ gives you a rough feedback about the power

consumption of the programme setting you selected. As soon as

you turn the programme selector to any programme, the „Eco

monitor“ is on.

The indicator on the left is to show that the „Eco monitor“

is active. The four indicators next to it show the degree of

consumption: the less power your programme setting is

forecasted to consume, the less indicators will light up. This

depends on the programme, temperature and options selected,

and also on the size of the wash load. For that reason, the

forecasted degree of power consumption may adapt when the

washing machine detects the wash load.

Whirlpool AWO-C 81400 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWO-C 81400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info