5019 301 06073
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives”
in your Instructions for Use.
1. Turn the
programme selector
to the desired
programme and temperature.
2. The
time display
shows the duration of the
chosen programme (in hours and minutes), and
the “Start/Pause” indication lamp is flashing.
3. The
indication lamp
of the predefined spin
speed lights up.
Push the button(s) of any option(s) desired - the
respective indication lights up.
When the combination of programme and
additional option(s) is not possible, the indication
lights switch off automatically. Unsuitable
combinations of options are deselected
automatically.
“Eco” button
• With a modified temperature profile and a
slightly prolonged wa
optimum combination of excellent washing
result and even lower energy consumption can
be achieved.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Incr
by approximately 15 min.
“Easy ironing” button
• Can be used together with “Cotton
“Synthetics” and “Daily load” programmes
make ironing easier
• Increases the water quantity and the clothes are
spun very gently
“Intensive rinse” butto
• More water is ad
• This option is particularly sui
very soft water
people with allergies.
“Rinse hold” button
• The laundry remains in
without progressing to the final spin cycle to
avoid creasing and prevent colours from
changing.
• This option is particular
programmes “Synth
“Delicates
• It is particular
spinning to a later time, or if you want to drain
only
Note:
The programme stops to “Ri
the time the “Anticrease” light in the programme
sequence indication is on. The indication lamp
next to the
“Start/P
button flashes.
T
•P
“Start/P
button; the
programme will termiautomatically with the
final spin cycle for the present wa
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain
programme and press the
“Start/P
button.
CONSUMPTION DATA
Progra
T
(°C)
Load
(kg)
Wa
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
Cotton / Antibacterial 95 6.0 59
**
1.90 2:00
Cotton 60 6.0 49 1.14 2:10
Cotton with “Eco”
***
60 6.0 49 1.02 2:20
Cotton 40 5.0 56 0.70 2:00
Synthetics 60 2.5 50
**
0.80 1:35
Synthetics 40 2.5 46 0.50 1:20
Delicates 30 1.5 60 0.50 0:45
Daily load 40 3.0 41 0.50 1:00
Quick wash 30 3.0 41 0.40 0:30
W 40 1.0 60 0.50 0:45
Handwash 40 1.0 45 0.50 0:40
Lingerie 30 1.0 45 0.40 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relae o
*
The remaining time indicator can deviate from the values in the table, because it takes into account the h
applicable at that time.
**
Twater is added at tut
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“
• Every programme has a predefi
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinni
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only
The “Start Delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is
• Select programme, temperature and options.
• Press the “Start Delay button to select the
delay time by 1 to 23 hours;
•P
“Start/P
button.
The indication light next to the “Start Delay
button lights up and the countdown of the delay
time begins.
• The time delay indication disappears when the
programme starts and it is replaced by the
remaining programme time.
• Once having pressed the
“Start/P
button,
the number of hours preselected can be redu
by pressing again the “Start Delay
T
..before you press the “Start/Pause” button:
• Tlector to ano
position or press the
“Res
button.
..after having pressed the “Start/P
button:
• Press the “Reset” button for
the start delay time disappears from the time
display
Open the tap and press the
“Start/P
button.
The indication lamp next to the
“Start/P
button lights up. The programme sequence
indicator shows the current programme phase,
running from left to right through Wash, Rinse, Spin/
Drain.
The time display shows the remaining programme
time. Due to variations in load and temperature of
inlet water, the remaining time is newly calculated in
certain programme phases. If this is the case, an
animation appears on the time display.
Before starting and after end of a programme, the
lamp lights to show that the door can be opened. As
long as a wash progr
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel
(Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component. Refer to the
“Troubleshooting Guide” in y
Use; if the fault persists, contact our After Sales
Service.
“Water tap closed”
The appliance has no or insufficient water
Open the water tap; if the indication still
refer to the “Troubleshooti
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filt
the latter case refer to the Instructions for Use
(“Removing the Filter”).
• All the lights of the programme sequence
indicator are off
indication lights up
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the
“Start/P
button to pause the
programme. The light flashes.
2. Select the new programme (with temper
any options and another spin speed if you want.
3. Press the
“Start/P
button again. The
new programme continues at the same position
where the previous programme was
interrupted. Do not add detergent for this
programme.
The
“Reset”
button cancels a programme before
the end.
•P
“Reset”
button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
START DELAY
PROG
“DOOR OPEN” INDICATION
RED INDICA
PROGRAMME END
CHANGE PROG
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30106073GB.f
Black process 45.0° 100.
