607060

Whirlpool AWO-D 6024 Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
ADD DETERGENTS, CLOSE THE DOOR AND
SELECT THE PROGRAMME
Load the laundry, close the door and add
detergents as indicated on the front page and
as described in the chapter “Detergent and
Additives” in your Instructions for Use.
Turn the programme selector to the desired
programme and temperature. The indication
lamp next to “Start/Pause” button blinks.
Your washing machine is designed to save
energy. After the end of a programme, or when a
programme is selected but not yet started, the
washing machine will therefore switch off
automatically after about a quarter of an hour.
To switch the washing machine on again,
turn the programme selector to “O” and
afterwards to the desired programme again.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. programme
duration
(hours : minutes)
%
Cotton with prewash
95 6.0 69 **** 2.10 2:18
55
Cotton
60 6.0 49 1.02 2:30
Cotton
40 6.0 54 0.65 2:00
Synthetics
60 3.0 50** 0.70 1:35
35
Synthetics
40 3.0 46 0.50 1:20
Delicates
30 1.5 50 0.50 0:46
Quick Wash
30 3.0 40 0.30 0:30
Wool/Hand
40 1.0 45 0.60 0:40
Wool/Hand
cold 1.0 45 0.10 0:35
Cotton
60°
*
60 6.0 49 0.78 4:00
53
Cotton
60°
*
60 3.0 37 0.69 2:20 ***
Cotton
40°
*
40 3.0 37 0.58 2:30 ***
Power consumption in off-mode 0.16 W / in left-on mode 0.16 W
SELECT ANY DESIRED OPTION
Push the button of any option desired - the
respective indication lamp lights up.
If the combination of programme and additional
option(s) is not possible, the indication lights
switch off automatically.
“Spin speed reduction” button
• Reduces the predetermined automatic
maximum spin speed to treat your laundry
more gently.
“Rinse hold” button
• The laundry remains in the last rinse water
without progressing to the final spin cycle
to avoid creasing and prevent colours from
changing.
• Particularly useful if you want to postpone
spinning to a later time, or if you want to drain
only.
• The programme stops to “Rinse hold” at
the time the “Rinse hold” indicator in the
programme flow bar is on. The indication lamp
next to the “Start/Pause” button blinks.
Terminate the “Rinse hold” option :
• Press the “Start/Pause” button ; the
programme will terminate automatically with
the final spin cycle for the present wash
programme.
• If you do not wish to spin the clothes, turn the
programme selector to the “Drain” programme
and press the “Start/Pause” button.
PROGRAMME START
Open the tap and press the “Start/Pause”
button. The indication lamp next to the “Start/
Pause” button lights up. The programme flow
bar shows the current programme phase,
running from left to right through Wash, Rinse,
Spin/Drain.
“DOOR OPEN” INDICATION
Before starting and after end of a programme,
the lamp lights to show the the door can be
opened. As long as a wash programme is
running, the door remains locked and must on
no account be forced open. In case you have
an urgent need to open it during a running
programme, refer to “Cancel (Reset) a running
programme before the end”.
FAILURE INDICATIONS
In case of any failures or irregularities, consult
the “Troubleshooting Guide” in your Instructions
for Use.
“Water tap closed”: no or not sufficient
inlet water.
”Service”: failure or malfunction of an
electrical component.
”Clean pump”: waste water is not pumped
out.
PROGRAMME END
The “Door open” indicator lights up. After about
a quarter of an hour, the washing machine will
switch off completely to save energy.
1. Turn the programme selector to the “O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1.
CHANGE PROGRAMME AND/OR OPTIONS AF-
TER PROGRAMME START
Press the “Start/Pause” button to pause the
programme. The light blinks.
2. Select the new programme (with
temperature), and any options if you want.
3. Press the “Start/Pause” button again. The
new programme continues at the same
position where the previous programme was
interrupted. Do not add detergent for this
programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme
before the end.
• Press and hold the “Reset” button for a few
seconds. Any existing water is drained out.
It may last some time until the door can be
opened.
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water
supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15°C through
the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply will lower the
energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions refer to the default
setting of the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption
data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
Approximate remaining moisture content (%). After programme and spinning with maximum selectable spin speed, in default programme setting.
* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle
temperature.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Automatic adaptation of programme duration after detection of wash load
**** Cool down water and prewash water
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Whirlpool AWO-D 6024 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Whirlpool AWO-D 6024

Whirlpool AWO-D 6024 Kurzanleitung - Deutsch - 2 seiten

Whirlpool AWO-D 6024 Bedienungsanleitung - Deutsch - 14 seiten

Whirlpool AWO-D 6024 Bedienungsanleitung - Englisch - 15 seiten

Whirlpool AWO-D 6024 Bedienungsanleitung - Holländisch - 14 seiten

Whirlpool AWO-D 6024 Kurzanleitung - Holländisch - 2 seiten

Whirlpool AWO-D 6024 Kurzanleitung - Französisch - 2 seiten

Whirlpool AWO-D 6024 Bedienungsanleitung - Französisch - 14 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info