Bedienungsanleitung Whirlpool AWO-D 7324 (Seite 10 von 12) (Englisch)

641525

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

GB 9

Failure

indicator blinks

Description - Causes - Solutions

“Water tap closed”

Appliance has no or insufﬁcient water supply. The “Start(Pause)” light blinks.

Check whether:

• Water tap is fully open and water supply pressure is sufﬁcient.

• Kinks are present in the water inlet hose.

• Mesh ﬁlter of water inlet hose is blocked (see “Care and Maintenance”.

• The water hose is frozen up.

• The safety valve inspection window of your water inlet hose is red (provided

your appliance has a water supply hose as shown on picture “13” - see chapter

“Care And Maintenance”); replace the hose by a new one available through our

After-Sales Service or your specialist dealer.

After problem has been removed, restart programme by pressing “Start(Pause)”.

If the fault occurs again, contact our After-Sales Service.

“Clean pump”

Waste water is not pumped out. The appliance stops in the corresponding

programme step; unplug it and check whether:

• Kinks are present in the drain hose, or the hose is blocked for another reason.

• Filter or pump is blocked (see chapter “Draining Residual Water/Cleaning The

Filter”); make sure the water has cooled before draining the appliance).

• The drain hose is frozen up.

After problem has been removed, push the “Reset” button for at least 3 seconds;

afterwards restart the desired programme. If the fault occurs again, contact our

After-Sales-Service.

If your washing machine has no display, check which of the previously described situations could be

the origin of the fault and follow the corresponding instructions.

ELECTRICAL CONNECTION

For Great Britain only

Warning - this appliance must be earthed.

Fuse replacement

If the mains lead of this appliance is ﬁtted with a BS

1363A 13amp fused plug, to change a fuse in this

type of plug use an A.S.T.A. approved fuse to BS

1362 type and proceed as follows:

1. Remove the fuse cover (A) and fuse (B).

2. Fit replacement 13A fuse into fuse cover.

3. Reﬁt both into plug.

Important:

The fuse cover must be reﬁtted when changing a fuse

and if the fuse cover is lost the plug must not be used

until a correct replacement is ﬁtted.

Correct replacement are identiﬁed by the colour insert

or the colour embossed in words on the base of the

plug. Replacement fuse covers are available from your

local electrical store.

For the Republic of Ireland only

The information given in respect of Great Britain will

frequently apply, but a third type of plug and socket is

also used, the 2-pin, side earth type.

Socket outlet / plug (valid for both countries)

If the ﬁtted plug is not suitable for your socket outlet,

Please contact After-Sales service for further

instruction.

Please do not attempt to change plug yourself. This

procedure needs to be carried out by a qualiﬁed

technician in compliance with the manufactures

instructions and current standard safety regulations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AWO-D 7324 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWO-D 7324

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info