5019 301 06076
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives”
in your Instructions for Use.
1. Push the
“On/Off”
button . The blue light
circle signals that the washer is switched on.
2. Select the
desired programme
by pushing the
corresponding programme button; it is marked
by a blue light.
3. The
temperature
and
spin speed
indicated on
the display can be altered by pressing the
“Temperature” button or the “Variable
spin” button .
When the combination of programme and
additional option(s) is not possible, the indication
lights switch off automatically. Unsuitable
combinations of options are deselected
automatically.
“Eco” button
• With a modified temperature profile and a
slightly prolonged washing duration, the
optimum combination of excellent washing
result and even lower energy consumption is
achieved.
“Easy ironing” button
• Can be used together with “Cotton
“Synthetics” and “Daily load” programmes to
make ironing easier
• Increases the water quantity and the clothes are
spun very gently
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time
by approximately 15 min.
• Do not use liquid detergent for the main wash
when activating the Prewash option.
“Intensive rinse” button
• More water is added and rinse cycle is
prolonged.
• This option is particularly suitable for areas with
very soft water or for washin
helps people with alle
“Rinse hold” button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and
“Delicates”.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain
only
• If you select “Rinse hold”, do not leave the
laundry to soak for too long.
Note:
The programme stops to “Rinse hold” at
the time the “Rinse hold” symbol on the
display lights up. The blue light under the
“Start/P
button flashes.
T :
• P
“Start/Pause”
button ; th
programme will terminate automatically with the
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, push
“Drain/Reset”
and then start the Drain
programme by pushing the
“Start/P
button .
CONSUMPTION DATA
Programme
Te m p e r a t u r e
(°C)
Load
(kg)
Wa
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
Cotton / Antibacterial 95 6.0 59
**
1.90 2:00
Cotton 60 6.0 56 1.14 2:10
Cotton with “Eco”
***
60 6.0 51 1.02 2:20
Cotton 40 5.0 56 0.70 2:00
Synthetics 60 2.5 50
**
0.80 1:35
Synthetics 40 2.5 46 0.50 1:20
Daily load 40 3.0 41 0.50 1:00
Quick wash 30 3.0 41 0.40 0:30
Delicates 30 1.5 60 0.50 0:45
W 40 1.0 60 0.50 0:45
Handwash 40 1.0 45 0.50 0:40
Consumption values were measured in normalized conditions in compliance with Standard6. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of w
*
The time indicated on the display can deviate from the the table, because it takes into account the household conditions
applicable at that time.
**
Twater is added at the end of the main wash cycle, but.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTIO
“
• Every programme has a predefined spin speed.
• P
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only
If there is a programme setting which you use
frequently, the appliance offers the possibility to
save one setting for each programme so that it can
be used again by just pushing one button.
• Select the desired programme, temperature,
spin speed and option(s), push and hold the
“Favourites”
button for at least 3 seconds.
The lamp next to
“Favourites”
shortly flashes
and then lights up - the programme setting is
saved.
Next time you want to use your individual
programme setting, select the programme, push the
“Favourites”
button and start by pushing
“Start/P
.
If you want to replace the saved programme
setting by another one:
• Push the programme button, select temperature,
spin speed and options as desired and then press
and hold the
“Favourites”
button for at least
3 seconds. The previously saved programme
setting will be replaced by the new one.
The “Start Delay” allows to run the machine at
the consumer’s convenience, for example at night
when electricity is cheaper.
• Select programme, temperature, spin speed and
options.
• P
time of 1, 3, 6, 9 or 12 hours.
• P
“Start/P
button .
The countdown of the delay time begins; the
clock symbol on the display and the delay time
selected flash.
• The delay time and the clock symbol disappear
when the programme starts.
• The number of hours preselected can be reduced
by pressing again the “Start Delay
T
• Select another programme or press the
“Drain/Reset”
button .
Open the tap and press the
“Start/P
button . The blue light under the
“Start/
Pa
button
is on. The programme sequence
indicator shows the current programme phase,
running from top to bottom through Wash, Rinse,
Spin/Drain.
Before starting and after end of a programme, the
lamp lights to show that the door can be open
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel
(Reset) a running programme before the end”.
“Water tap closed”
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the “Troubleshooting Guide” in the
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
“Service”
Lighting up of the “Service” indication can be caused by
a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your Instructions for Use;
if the fault persists, contact our After Sales Ser
• The light of the programme sequence indicator
is offen lights
up.
1. Switch the machine off by pushing
“On/
Off”
.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the
“Start/P
button to pause
the programme. The light flashes.
2. Select the new programme, temperature, any
options and another spin speed if you want.
3. Press the
“Start/P
button again. The
new programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
The
“Drain/Reset”
button cancels a
programme before the end.
• Press the
“Drain/Reset”
button for at
least 3 seconds. Any existing water is drained
out before the door can be opened.
SA
START DELAY
PRO
“DOOR OPEN” INDICATION
RED INDICA
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30106076GB.fm Page 2 Friday, July 13, 2007 6:44 PM
Black process 45.0° 100.0 LPI
