Bedienungsanleitung Whirlpool AWO7140 (Seite 2 von 2) (Englisch)

586302

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 301 05667

Whirlpool is a registered trademark of Whirlpool USA

Add the detergents as described in the programme

table or in the chapter “Detergents and Additives”

in the booklet.

1. Turn the

programme selector knob

to the

desired programme.

2. The indication of the

“Start/Pause”

button is

flashing.

3. The programme sequence and the predefined

spin speed indication corresponding to the

selected programme lights up.

Selecting any option the indication lights up.

When the combination of programme, additional

options and temperature is not possible, the

indication lights switch off automatically. Unsuitable

combinations of options are deselected

automatically.

“Easy Ironing” button

• Can be used together with “Cotton”, “Synthetics”

and “Daily” programmes to make ironing easier.

• Increases the water quantity and the clothes are

spun very soft.

“Eco” button

• The duration of the wash is extended and the

temperature reduced to save up to 40% of

energy but maintaining good washing results.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. The cycle time increases

approximately 15 min.

“Intensive Rinse” button

• More water and a longer time in rinse cycle is added.

• This option is particularly suitable for areas with

very soft water, washing baby linen and helps

people with allergies.

“Rinse Hold” button

• The laundry remains in the last rinse water

without progressing to the final spin cycle to

avoid creasing and prevent colours from

changing.

• This option is particularly recommended for the

programme “Synthetics”, “Daily” and

“Delicates”.

CONSUMPTION DATA

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx.

Programme

Duration

(hours : minutes)

Cotton 95 5.5 54* 1.90 2:00

Cotton 60 5.5 49 1.04 2:20

Cotton 40 5.0 44 0.60 2:05

Synthetics 60 2.5 55 0.80 1:30

Synthetics 40 2.5 55 0.60 1:20

Daily 40 3.0 45 0.50 1:00

Superrapid 30 3.0 37 0.40 0:30

Delicates 30 1.5 60 0.50 0:45

Wool 30 1.0 60 0.30 0:40

Silk 30 1.0 45 0.30 0:40

Prewash cycle might increase programme duration. Consumption values were measured in normalized conditions in compliance

with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the

water supply pressure and temperature, the load and the type of wash.

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the

water out.

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

• This function is particularly useful if you want to

postpone spinning to a later time, or if you want

to drain only.

Note:

The programme stops to “Rinse Hold” at

the time the “Rinse Hold” light in the programme

sequence indication is on.

Terminate the “Rinse Hold” option:

• Press the “Rinse Hold” button again; the

programme will terminate automatically with the

final spin cycle for the present wash programme.

• If you do not wish to spin the clothes, turn the

programme selector knob counterclockwise to

the “Drain” programme and press the

“Start/Pause”

button again when the indication

next to it is flashing.

“Spin Speed” button

• Every programme has an automatic predefined

maximum spin speed.

• Press the button to set another spin speed.

• If the spin speed “0” is selected, the final spinning is

cancelled but intermediate spin peaks remain

during rinse. The water is drained out only.

Open the tap and press the

“Start/Pause”

button.

The indication next to the

“Start/Pause”

button

lights up.

The indications show the sequence reached in the

programme. After starting the programme, the

sequence indication runs from left to right through

Wash, Rinse, Spin.

When the sequence of the programme is finished

the corresponding indication goes out.

“Water Tap Closed”

The appliance has no or insufficient water supply.

Open the water tap; if the indication still lights up,

refer to the “Troubleshooting Guide” in the

Instructions for Use.

“Clean Pump”

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned; in

the latter case refer to the Instructions for Use

(“Removing the Filter”).

“Door Locked”

As long as a washing programme is running, the

lamp lights up to show that the door cannot be

opened. When the indication goes off, the door can

be opened again.

• All the lights of the programme sequence

indication are off.

1. Turn the programme selector to the

“

Off

/0”

position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry out.

1. Press the

“Start/Pause”

button to pause the

programme. The light flashes.

2. Select the new programme (with temperature),

any options and another spin speed if you want.

3. Press the

“Start/Pause”

button again. The new

programme continues at the same position where

the previous programme was interrupted. Do not

add detergent for this programme.

The

“Reset”

button cancels a programme before

the end.

•Press the

“Reset”

button for at least 3 seconds.

Any existing water is drained out before the

door can be opened.

PROGRAMME START

RED INDICATIONS

PROGRAMME END

CHANGE THE PROGRAMME,

TEMPERATURE, OPTIONS AFTER

PROGRAMME START

CANCEL (RESET) A RUNNING

PROGRAMME BEFORE THE END

3gb05667.fm Page 2 Wednesday, August 4, 2004 5:32 PM

Black process 45.0° 100.0 LPI

Whirlpool AWO7140 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWO7140

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info