Bedienungsanleitung Whirlpool AWOA7123 (Seite 11 von 16) (Englisch)

650585

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

EN 9

Problem Causes - Solutions - Tips

Detergent residues

on laundry after wash

Whitish residues on dark fabrics are caused by insoluble compounds used in

phosphate-free powder detergents:

- avoid overdosing of detergent; use liquid detergent; select “Intensive Rinse” op-

tion if possible; brush out the fabric.

Programme duration

is considerably

longer or shorter

as indicated in the

“programme chart”

or on the display (if

available)

Normal function of the washing machine to adapt to factors that can have an

effect on the programme duration, like excessive foam formation, load unbalance

due to heavy laundry items, prolonged heating time resulting from low inlet water

temperature etc. Moreover, the sensing system of the washing machine adapts the

programme duration to the size of the wash load.

Depending on these factors, the duration is recalculated during the

programme and updated if necessary; during such periods, an animation

appears on the display (if available). For small loads, the programme time

indicated in the “programme chart” may be reduced by up to 50%.

Description of failure indicators

Failure

indicator blinks

Indication on display

(if available)

Description - Causes - Solutions

“Service”

from “F03” to “F43”

(except “F18” and “F24”)

“Electrical module fault”

Push the “Reset” button for at least 3 seconds.

“F24”

May appear for very water-soaking laundry, or if you

added too much laundry for a programme destined for

small loads only. Do not overload the washing ma-

chine. Push the “Reset” button for at least 3 seconds

to stop the programme. Select and start “Rinse and

Spin” programme to complete the interrupted wash

programme properly.

“F02” or “FA”

“Waterstop fault”

Turn the programme selector to the “Off/O” position,

pull out the mains plug and turn the water tap off.

Then:

• Plug in the appliance again.

• Turn the water tap on (if water immediately ﬂows

into the appliance without the appliance being

started, there is a failure; turn off the tap and notify

the After-Sales Service).

• Select and start the desired programme again.

“F18” or “Fod”

“Overfoaming”

Too much foam interrupted the wash programme.

If your washing machine has a “Dosing Aid” function,

and you used it: check if the dosing values set for the

different programme groups correspond to the dosing

values recommended for the detergents you use (see

details in separate Instructions for the “Dosing Aid”).

• Select and start the “Rinse & Spin” programme.

• Afterwards select and start the desired programme

again, using less detergent. See also paragraph

“The machine is at a standstill....” on ﬁrst page of

Troubleshooting Guide.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AWOA7123 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWOA7123

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info