Bedienungsanleitung Whirlpool AWOD 7234 (Seite 13 von 13) (Englisch)

563703

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

Noise, excessive vibrations and water leakages

can be caused by incorrect installation of washing

machine.

If your washing machine is NOT a built-in model

NEVER move the appliance by carrying it at the

worktop.

REMOVE TRANSPORT BOLTS! (pict.1)

Important:

- Not removed transport bolts cause damages

to the appliance!

- Keep the transport bolts for further

transporting of the appliance; in this case

refit the transport bolts in reverse order.

1. Loosen the screws of all 4 transport bolts by

about 35 mm (pict. 2a).

2. Push screw inside of machine to stop position

(min. 20 mm) (pict. 2b).

3. Pull out the rubber rings from the holes (do not

pull the screws!). The whole transport bolt can

be removed now (pict. 2c).

4. Push the plastic caps delivered with your

washing machine on the holes to close them

(pict. 2d).

ADJUSTMENT OF THE FEET

The appliance must be installed on a solid and level

floor surface (if necessary use a spirit level).

If the appliance is to be installed on a wooden or

floating floor, distribute the weight by placing it on a

sheet of plywood measuring at least 60 x 60 cm and

thickness of at least 3 cm which is secured to the

floor. If the floor is uneven, adjust the 4 levelling feet

as required; do not insert pieces of wood etc. under

the feet.

Screw out the washing machine´s feet by hand with

2-3 clockwise turns and then slacken the locknut by

wrench (see pict. 3, 4).

Slightly lift the machine and adjust the height of the

foot revolving it (pict. 4).

Important: tighten the locknut by turning it anti-

clockwise towards the appliance casing (pict. 5, 6).

CONNECT THE WATER INLET HOSE

If the water inlet hose is not already installed, screw

by hand the bent end of the inlet hose to the valve on

the washing machine‘s back (pict. 7, 8).

Screw by hand the straight end of the inlet hose to

the tap, tightening the nut.

Attention:

• No kinks in the hose!

• The appliance must not be connected to the

mixing tap of an un-pressurized water heater.

• Check water-tightness of connections by turning

the tap completely on.

• If the hose is too short, replace it with a suitable

length of pressure resistant hose (1000 kPa min,

EN 50084 approved type).

INSTALLATION GUIDE

Pictures are on the cover of this Instruction for Use

GB 13

If you need a longer waterstop hose, contact

our After Sales Service or your dealer.

• Check the inlet hose regularly for brittleness

and cracks and replace if necessary.

• The washing machine can be connected without

a backflow valve.

CONNECT THE DRAIN HOSE

1. In case the drain hose is installed as shown on

pict. 9: Unclip it from the holders marked with

arrows.

2. In case the drain hose is installed in the upper

part of the washing machine (pict. 10): Unclip it

from both holders marked with arrows

(depending on the model ).

3. Firmly connect the drain hose to the siphon, or

another outlet for drain water.

• Make sure there are no kinks in the drain hose.

• Secure the hose so that it cannot fall down.

• Small hand basins are not appropriate.

• To make an extension, use a hose of the same

type and secure the connections with clips.

• Height for siphon - drain hose connection must

be minimum 60 cm and maximum 125 cm

• Max. Overall drain hose length: 2,50 m (in this

case, the maximum height for fixation is 90 cm).

ELECTRICAL CONNECTION

• Use a socket with an earth connection.

• Do not use extension leads or multi sockets.

• The electrical power cable must be replaced

exclusively by a licensed electrician.

• Electrical connections must be made in accordance

with local regulations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AWOD 7234 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWOD 7234

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info