Bedienungsanleitung Whirlpool DLCE 71469 (Seite 13 von 16) (Englisch)

650530

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

EN 11

INSTALLATION GUIDE

Pictures are on the cover of this Instruction for

Use.

For built-in washing machines: observe the

separate Built-in Instructions.

Noise, excessive vibrations and water leakages

can be caused by incorrect installation of washing

machine.

For freestanding models: NEVER move the

washing machine by carrying it at the worktop.

REMOVE TRANSPORT BOLTS! (pict.15)

Important:

- Not removed transport bolts cause damages to

the appliance!

- Keep the transport bolts for further

transporting of the appliance; in this case reﬁt

the transport bolts in reverse order.

1. Loosen and screw out the screws of all 4 transport

bolts; use a 13 mm wrench (pict. 16a,b).

2. Afterwards screw in the screws again just by about

2 cm; then pull out the plastic parts from the back

of the washing machine by wobbling and pulling on

the screws (pict. 16c, d, e).

3. Push the plastic caps delivered with your washing

machine on the openings to close them (pict. 16f).

ADJUSTMENT OF THE FEET

The appliance must be installed on a solid and level

ﬂoor surface (if necessary use a spirit level).

If the appliance is to be installed on a wooden or

ﬂoating ﬂoor, distribute the weight by placing it on a

sheet of plywood measuring at least 60 x 60 cm and

thickness of at least 3 cm which is secured to the

ﬂoor. If the ﬂoor is uneven, adjust the 4 levelling feet

as required; do not insert pieces of wood etc. under

the feet.

Screw out the washing machine´s feet by hand with

2-3 clockwise turns and then slacken the locknut by

13 mm wrench (pict. 17, 18).

Slightly lift the machine and adjust the height of the

foot revolving it (pict. 18).

Important: tighten the locknut by turning it anti-

clockwise towards the appliance casing (pict. 19, 20).

CONNECT THE WATER INLET HOSE

If the water inlet hose is not already installed, screw

by hand the bent end of the inlet hose to the valve

on the washing machine‘s back (pict. 21, 22). Screw

by hand the straight end of the inlet hose to the tap,

tightening the nut.

Attention:

• No kinks in the hose!

• The appliance must not be connected to the

mixing tap of an un-pressurized water heater.

• Check water-tightness of connections by

turning the tap completely on.

• If the hose is too short, replace it with a suitable

length of pressure resistant hose (1000 kPa min,

EN 61770 approved type). If you need a longer

waterstop hose, contact our After Sales Service or

your dealer.

• Check the inlet hose regularly for brittleness and

cracks and replace if necessary.

• The washing machine can be connected without a

backﬂow valve.

CONNECT THE DRAIN HOSE

1. In case the drain hose is installed as shown on

pict. 23: Unclip it from the holders marked with

arrows.

2. In case the drain hose is installed in the upper part

of the washing machine (pict. 24): Unclip it from

both holders marked with arrows (depending on

the model ).

3. Firmly connect the drain hose to the siphon or

another outlet for drain water.

• Make sure there are no kinks in the drain hose.

• Secure the hose so that it cannot fall down.

• Small hand basins are not appropriate.

• To make an extension, use a hose of the same

type and secure the connections with clips.

• Height for siphon - drain hose connection must be

minimum 60 cm and maximum 125 cm

• Max. Overall drain hose length: 2,50 m (in this

case, the maximum height for ﬁxation is 90 cm).

ELECTRICAL CONNECTION

• Use a socket with an earth connection.

• Do not use extension leads or multi sockets.

• The electrical power cable must be replaced

exclusively by a licensed electrician.

• Electrical connections must be made in

accordance with local regulations.

K - 10/2014

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool DLCE 71469 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool DLCE 71469

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info