Bedienungsanleitung Whirlpool easy 1400 (Seite 2 von 2) (Englisch)

304768

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 301 05818

Whirlpool is a registered trademark of Whirlpool USA

Add the detergents as described in the programme

table or in the chapter “Detergents and Additives”

in your Instructions for Use booklet.

1. Switch on the machine by pressing the

“On/Off”-button.

2. The blue indication lights of the main programmes

and of the “Reset/Drain” button light up.

3. Select the desired programme by pressing the

corresponding button. The blue lamps of the other

programmes go out, and the lamp of the “Start/

Pause” button flashes. The display shows the

predefined spin speed and temperature

corresponding to the selected programme.

4. The temperature can be altered by pressing the

temperature selection buttons “+/-”, the spin

speed by pressing the spin speed selection button

. If spin speed “0” is selected, the final spinning

is cancelled, but intermediate spin peaks remain

during rinse; the water is drained out only.

Selecting any special option the indication lights up.

When the combination of programme, additional

options and temperature is not possible, the indication

lights switch off automatically. Unsuitable

combinations of options are deselected automatically.

“Easy Ironing” button

• Can be used together with “Cotton”, “Synthetics”

and “Daily” programmes to make ironing easier.

• Increases the water quantity and the clothes are

spun very soft.

“Eco” button

• The duration of the wash is extended and the

temperature reduced to save up to 40% of

energy but maintaining good washing results.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. The cycle time increases

approximately 15 min.

“Intensive Rinse” button

• More water and a longer time in rinse cycle is added.

• This option is particularly suitable for areas with

very soft water, washing baby linen and helps

people with allergies.

“Rinse Hold” button

• The laundry remains in the last rinse water

without progressing to the final spin cycle to avoid

creasing and prevent colours from changing.

• This option is particularly recommended for the

programme “Synthetics”, “Daily” and “Delicates”.

• This function is particularly useful if you want to

postpone spinning to a later time, or if you want

to drain only.

Note: The programme stops to “Rinse Hold” at

the time the “Rinse Hold” symbol is indicated on

the display. The “Start/Pause” button flashes.

CONSUMPTION DATA

Programme

Temperature

Selector

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)*

Cotton 95 6.0 54** 1.90 2:00

Cotton 60 6.0 49 1.14 2:20

Cotton 40 5.0 44 0.60 2:05

Synthetics 60 2.5 55 0.80 1:30

Synthetics 40 2.5 55 0.60 1:20

Daily load 40 3.0 45 0.50 1:00

Quick wash 30 3.0 37 0.40 0:30

Delicate 30 1.5 60 0.50 0:45

Wool 30 1.0 60 0.30 0:40

Handwash 30 1.0 45 0.30 0:40

Prewash cycle might increase programme duration. Consumption values were measured in normalized conditions in compliance

with Standard IEC / EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the

water supply pressure and temperature, the load and the type of wash.

* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the household

conditions applicable at that time. When the remaining programme duration is newly calculated, the 6th sense symbol

appears on the display.

** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT SPECIAL OPTIONS

Terminate the “Rinse Hold” option:

• Press the “Start/Pause” button; the

programme will terminate automatically with the

final spin cycle for the present wash programme.

• If you do not wish to spin the clothes, press the

“Reset/Drain” button and afterwards the “Start/

Pause” button to start the “Drain” programme.

You have the possibility to store, for each main

programme, your preferred combination of

programme, options, temperature and spin speed.

After having selected the desired combination,

press the “Favourites” button for at least 3 sec.

Next time you choose the corresponding

programme, the display will show you the stored

parameters, and you just have to press “Start/

Pause”. If you want to change the stored

combination, just make your new choice and again

press the “Favourites” button for at least 3 sec.

The previous combination is cancelled

automatically, and the new one is stored.

The “Start Delay” allows to run the machine at the

consumer’s convenience, for example at night when

electricity is cheaper.

• Select programme, temperature, spin speed and

options.

• Press the “Start Delay” button to select the

delay time by 1 to 23 hours. The selected start

delay is indicated on the display under

“Remaining Time”.

• Press the “Start/Pause” button - the

countdown of the selected start delay begins.

• The start delay indication disappears when the

programme starts and is replaced by the

remaining time.

• The number of hours can be modified later by

pressing the “Start Delay” button again.

To cancel the “Start Delay”

• Press the "Reset" button for at least 3 seconds -

the start delay time disappears from the

remaining time indication.

Open the tap and press the “Start/Pause” button.

The blue lamp under the “Start/Pause” button

stops flashing and lights up. The display indicates the

sequence reached in the programme by the

corresponding symbol. When the programme

sequence is finished, the corresponding symbol

disappears. Under “Remaining Time”, the display

indicates the remaining programme duration.

As long as a washing programme is running, the lamp

lights up to show that the door cannot be opened. When

the indication goes off, the door can be opened again.

“Clean filter”

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned; in

the latter case refer to the Instructions for Use

(“Removing the Filter”).

“Water tap closed”

The appliance has no or insufficient water supply. Open

the water tap; if the indication still lights up, refer to the

“Troubleshooting Guide” in the Instructions for Use.

“Aquastop”

Lighting up of the water stop indication can be caused

by a leak in the appliance or hose. Please refer to the

“Troubleshooting Guide” in the Instructions for Use.

• On the display, the “Remaining time” disappears

and “End” is indicated.

1. Switch the machine off by pressing the

“On/Off”-button.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry out.

1. Press the “Start/Pause” button to pause the

programme. The light flashes.

2. Select the new programme (with temperature),

any options and another spin speed if you want.

3. Press the “Start/Pause” button again. The new

programme continues at the same position where

the previous programme was interrupted. Do not

add detergent for this programme.

•Press the “Reset/Drain” button for at least 3

seconds. Any existing water is drained out

before the door can be opened.

FAVOURITES

START DELAY

PROGRAMME START

BLUE “DOOR LOCKED” INDICATION

RED INDICATIONS

PROGRAMME END

CHANGE THE PROGRAMME,

TEMPERATURE, OPTIONS AFTER

PROGRAMME START

CANCEL (RESET) A RUNNING

PROGRAMME BEFORE THE END

Whirlpool easy 1400 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool easy 1400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info