Bedienungsanleitung Whirlpool emotion 1400 (Seite 2 von 2) (Englisch)

304693

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 301 05768

Whirlpool is a registered trademark of Whirlpool USA

Add the detergent as described in the programme

table or in the chapter “Detergents and Additives”

in the booklet.

1. Turn the programme selector knob to the

desired programme and temperature.

2. The remaining time display shows the duration

of the chosen programme (in hours and minutes)

and after taking some seconds for calculating, the

indication of the “Start/Pause” button is flashing.

3. The programme sequence and the predefined

spin speed indication corresponding to the

selected programme lights up.

Selecting any option the indication lights up.

When the combination of programme, additional

options and temperature is not possible, the indication

lights switch off automatically. Unsuitable

combinations of options are deselected automatically.

“Easy Ironing” button

• Can be used together with “Cotton”, “Synthetics”

and “Daily” programmes to make ironing easier.

• Increases the water quantity and the clothes are

spun very soft.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. The cycle time increases

approximately 15 min.

“Intensive Rinse” button

• More water and a longer time in rinse cycle is added.

• This option is particularly suitable for areas with

very soft water, washing baby linen and helps

people with allergies.

“Rinse Hold” button

• The laundry remains in the last rinse water

without progressing to the final spin cycle to avoid

creasing and prevent colours from changing.

• This option is particularly recommended for the

programme “Synthetics”, “Daily” and “Delicates”.

• This function is particularly useful if you want to

postpone spinning to a later time, or if you want

to drain only.

Note: The programme stops to “Rinse Hold” at

the time the “Rinse Hold” light in the programme

sequence indication is on.

CONSUMPTION DATA

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx.

Programme

Duration

(hours : minutes)

Cotton 95 5.0 49* 1.90 2:00

Cotton 60 5.0 44 0.95 2:20

Cotton 40 4.5 44 0.60 2:05

Synthetics 60 2.5 55 0.80 1:30

Synthetics 40 2.5 55 0.60 1:20

Daily 40 3.0 45 0.50 1:00

Superrapid 30 3.0 37 0.40 0:30

Delicates 40 1.5 60 0.60 0:45

Wool 30 1.0 60 0.30 0:40

Handwash 30 1.0 45 0.30 0:40

Prewash cycle might increase programme duration. Consumption values were measured in normalized conditions in

compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in

relation to the water supply pressure and temperature, the load and the type of wash.

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains

the water out.

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

Terminate the “Rinse Hold” option:

• Press the “Rinse Hold” button again; the

programme will terminate automatically with the

final spin cycle for the present wash programme.

• If you do not wish to spin the clothes, turn the

programme selector knob counterclockwise to

the “Drain” programme and press the

“Start/Pause” button again when the indication

next to it is flashing.

“Spin Speed” button

• Every programme has an automatic predefined

maximum spin speed.

• Press the button to set another spin speed.

• If the spin speed “0” is selected, the final spinning is

cancelled but intermediate spin peaks remain

during rinse. The water is drained out only.

Open the tap and press the “Start/Pause” button.

The indication next to the “Start/Pause” button

lights up. The indications show the sequence

reached in the programme. After starting the

programme, the sequence indication runs from left

to right through Wash, Rinse, Spin.

When the sequence of the programme is finished

the corresponding indication goes out.

“Water Tap Closed”

The appliance has no or insufficient water supply. Open

the water tap; if the indication still lights up, refer to the

“Troubleshooting Guide” in the Instructions for Use.

“Clean Pump”

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned; in

the latter case refer to the Instructions for Use

(“Removing the Filter”).

“Door Locked”

As long as a washing programme is running, the lamp

lights up to show that the door cannot be opened. When

the indication goes off, the door can be opened again.

• The remaining time is on “0:00” and all the lights

of the programme sequence indication are off.

1. Turn the programme selector to the

“

Off

/0”

position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry out.

1. Press the “Start/Pause” button to pause the

programme. The light flashes.

2. Select the new programme (with temperature),

any options and another spin speed if you want.

3. Press the “Start/Pause” button again. The new

programme continues at the same position

where the previous programme was interrupted.

Do not add detergent for this programme.

The “Reset” button cancels a programme before

the end.

• Press the “Reset” button for at least 3

seconds. Any existing water is drained out

before the door can be opened.

PROGRAMME START

RED INDICATIONS

PROGRAMME END

CHANGE THE PROGRAMME, OPTIONS

AFTER PROGRAMME START

CANCEL (RESET) A RUNNING

PROGRAMME BEFORE THE END

30105768GB.fm Page 2 Tuesday, June 28, 2005 4:31 PM

Black process 45.0° 100.0 LPI

Whirlpool emotion 1400 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool emotion 1400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info