Bedienungsanleitung Whirlpool FFTM119X2BXY BE (Seite 4 von 4) (Englisch)

793902

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.

In order to receive a more complete assistance, please

Policies, standard documentation, ordering of spare parts and additional product information can be

found by:

• Visiting our website docs.whirlpool.eu and parts-selfservice.whirlpool.com

• Using QR Code

• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When

contacting our After-sales Service, please state the codes provided on your product’s identi cation plate.

Quick guide

Before using the appliance carefully read the Safety

Instruction.

xxxxxxxxxxxx

xxxx

TROUBLESHOOTING EN

Before contacting the After-sales Service, refer to the table below. Often the malfunctions are minor and can be solved in few

minutes.

Malfunction Possible cause Solution

The tumble

dryer does not

turn on.

The plug is not inserted into the socket.

Insert the plug into the socket.

The plug is faulty.

Try to plug another appliance in the same socket. Do not use

connecting electrical devices to the socket, such as adapters or

extensions.

A power failure occurred.

Wait for the power supply to be restored and switch the fuse on again

if necessary.

The tumble

dryer does not

start.

The door has not been closed properly.

Close the door.

A time delay was set to the start of the cycle. For machines equipped with this function: wait for the set delay to

end or switch the machine o to reset it. Refer to the Options section.

The "Start/Pause" button was not pressed in

order to start the programme.

Press the "Start/Pause" button.

The Key Lock function was enabled (for machines

equipped with this option).

Refer to the Options section. If Key Lock was selected, disable it.

Switching the machine o will not disable this option.

Garments are

wet at cycle

completion.

Small load.

The automatic programme has not sensed the required  nal moisture

so that the dryer completes the programme and stops. If this happens

simply select an additional short period of drying or select Extra Dry

option if available.

Large loads or heavier fabrics. Dryness levels can be modi ed to the speci c dryness desired.

Extra Dry is recommended for ready to wear items.

The drying

times are very

long.

An appropriate maintenance was not carried out. Refer to the Care & Maintenace section and perform the operations

described.

The programme, the time and/or the drying level

set are not suitable for the type and the amount

of load inserted into the dryer.

Refer to Programmes and Options sections to  nd the programme

and options most suitable for the type of load.

The garments are too wet.

Carry out a washing cycle with higher spin speed to remove as much

water as possible.

The dryer may be overloaded. Refer to the Programmes section to check the max load for each

programme.

Room temperature. The drying time may be longer if the room temperature falls outside

the 14–30°C range.

The programme

did not end.

A power failure occurred might have occurred. In case of power failure, it is necessary to press the "Start/Pause"

button to restart the cycle.

Lights on or  ashing

Water tank The water tank is full. Empty the water tank. Refer to the Care & Maintenance section.

Door  lter Failure of the air  ow necessary for machine

operation.

Clean the door  lter and check whether air intake is free. Carrying

out these operations improperly may cause damages. Refer to Care &

Maintenance section.

Bottom  lter* The bottom  lter requires cleaning. Clean the bottom  lter. Refer to Care & Maintenance section.

DEMO

The cycle lasts

few minutes.

The dryer is in DEMO mode. The DEMO indicator

is on.

Disable the DEMO mode. The following actions must be carried out in

sequence, without breaks. Switch the machine on and then switch it o

again. Press the Start/Pause button until the buzzer is heard. Switch the

machine on again. The “DEMO” indicator  ashes and then turns o .

The presence

of wrench

symbol signals a

malfunction.

The machine sensors detected a failure.

Switch the dryer o and unplug it. Open the door immediately and

pull laundry out, to allow the heat to dissipate. Wait for about 15

minutes. Reconnect the dryer to the power supply, load the laundry

and restart the drying cycle. If the problem still occurs, contact

the After-Sales Service Centre and communicate the letters and

digits  ashing on the display.

For instance: F3 and E2.

*Note: some models are auto-cleaning and not equipped with bottom  lter. Please refer to the Care & Maintenance section.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool FFTM119X2BXY BE Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool FFTM119X2BXY BE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info