Bedienungsanleitung Whirlpool FSCR 10420 (Seite 6 von 54) (Englisch)

607067

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

discarded.

Move the appliance without

lifting it by the worktop.

Connect the water inlet

hose(s) to the water supply

in accordance with the

regulations of your local water

company.

For models dedicated only for

cold water: Do not connect to

the hot water supply.

For models with hot ll: the

hot water inlet temperature

must not exceed 60 °C.

Make sure that the ventilation

openings in the base of

your washing machine (if

available on your model) are

not obstructed by a carpet or

other material.

The supply water pressure

must be in range 0.1-1 MPa.

If you want to place a dryer

on top of your washing

machine, rst contact our

After-Sales Service or your

specialist dealer to verify if

this is possible. This is only

admitted if the dryer is xed

on the washing machine by

using an appropriate stacking

kit available through our After-

Sales Service or your specialist

dealer.

ELECTRICAL WARNINGS

Make sure the voltage

specied on the rating plate

corresponds to that of your

home.

This washing machine is

exclusively destined to treat

machine washable laundry in

quantities which are usual for

private households.

INSTALLATION

Installation and repairs must

be carried out by a qualied

technician, in compliance

with the manufacturer’s

instructions and local safety

regulations. Do not repair

or replace any part of the

appliance unless specically

stated in the user manual.

Use protective gloves to

perform all unpacking and

installation operations.

The appliance must be

disconnected from the power

supply before carrying out any

installation operation.

Only activate the appliance

when the installation

procedure has been

completed.

After unpacking the appliance,

make sure that it has not been

damaged during transport. In

the event of problems, contact

the dealer or your nearest

After-sales Service.

During installation, make

sure the appliance does not

damage the power cable.

The appliance must be

handled and installed by two

or more persons.

When installing the appliance

make sure that the four feet

are stable and resting on

the oor, adjusting them as

required, and check that the

appliance is perfectly level

using a spirit level.

Remove the bottom

protection by tilting and

turning the washing machine

on one rear bottom corner.

Make sure that the plastic

part of the bottom protection

(if available on the model)

remains in the packing and

not in the machine bottom.

This is important, as otherwise

the plastic part could damage

the washing machine during

operation.

If the appliance was exposed

to the cold prior to delivery,

keep it at room temperature

for a few hours before

operating.

Do not install your appliance

where it may be exposed to

extreme conditions, such as:

poor ventilation, temperature

below 5°C or above 35°C.

In case of wooden or so-called

“oating oors” (for instance

certain parquet or laminate

oors), place the appliance

on a sheet of plywood at least

60 x 60 cm wide/ deep and

at least 3 cm thick which is

secured to the oor.

Use only new hoses to connect

the appliance to the water

supply. Used hoses must

not be used and should be

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool FSCR 10420 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool FSCR 10420

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info