Bedienungsanleitung Whirlpool green 1400 (Seite 7 von 12) (Englisch)

315397

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

GB 7

CARE AND MAINTENANCE

Appliance exterior and control panel

•

Can be washed down with a soft, damp cloth.

•

A little neutral detergent (non abrasive) can also

be used.

•

Dry with a soft cloth.

Appliance interior

•

After each washing, leave the door open for some

time to allow the inside of the appliance to dry.

•

If you never or seldom wash your laundry at

95°C, we recommend to occasionally run a 95°C

programme without laundry, adding a small

amount of detergent, to keep the interior of the

appliance clean.

Door seal

•

Dry the door seal after each washing with an

absorbent cotton cloth; make sure that the door

seal is completely dry before closing the door of

the empty washing machine.

•

Check the condition of the door seal periodically.

Filter

•

Check and clean the filter regularly, at least two

or three times a year (see “Draining Residual

Water/ Cleaning The Filter”).

Do not use flammable fluids for cleaning

the appliance.

Detergent dispenser

Clean the dispenser drawer and the dispenser compartment

regularly, at least three or four times a year, to prevent

detergent build-up.

To clean the dispenser drawer:

Press the release lever in the main wash chamber downward and

remove the dispenser drawer from the dispenser compartment

(see downward arrow).

Remove the cover grid from the softener chamber. Remove the

separator from the main wash chamber by pulling it upward (see

upward arrows).

Wash all the parts under running water.

Clean the dispenser compartment with a damp cloth.

Refit the separator and the cover grid in the dispenser drawer

and push the drawer back into the dispenser compartment.

Water supply hose(s) (picture A, B or C - depending on

model)

Check regularly for brittleness and cracks. If a supply hose shows a

damage, replace it by a new hose of the same type, available through

our After-Sales Service or your specialist dealer.

If the inlet hose of your washing machine corresponds with the

model on picture “

”, periodically check the safety valve inspection

window: if it is red, the hose's waterstop function was triggered, and

the hose must be exchanged by a new one from our After-Sales

Service or your specialist dealer.

If your supply hose has a transparent hose coating (fig. “

”),

periodically check the colour. If the hose colour intensifies locally,

this is an indication that the hose may have a leak and should be

replaced. Contact our After-Sales Service team or specialist dealer

to obtain a replacement hose.

Cleaning the mesh filter in the water supply hose(s)

Close the tap and loosen the inlet hose on the tap.

Clean the internal mesh filter and screw the water inlet hose back

onto the tap.

Now unscrew the inlet hose on the rear of the washing machine.

Pull off the mesh filter from the washing machine connection

with universal pliers and clean it.

Refit the mesh filter and screw the inlet hose on again.

Turn on the tap and ensure that the connections are completely

water-tight.

Safety valve

inspection

window

30106300aGB.fm Page 7 Friday, January 8, 2010 5:08 PM

Black process 45.0° 130.0 LPI

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool green 1400 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool green 1400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info